 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Features * * * * * * * * * * * * * * * * AVR(R) 8-bit RISC Microcontroller with 83 ns Instruction Cycle Time USB Hub with One Attached and Four External Ports USB Keyboard Function with Four Programmable Endpoints 16 KB Program Memory, 512-Byte Data SRAM 32 x 8 General-purpose Working Registers 42 Programmable I/O Port Pins Support for 20 x 8 Keyboard Matrix Keyboard Scan Inputs with Pull-up Resistor Four LED Driver Outputs One 8-bit Timer/Counter with Separate Pre-scaler One 16-bit Timer/Counter with Separate Pre-scaler and Dual 8-, 9- or 10-bit PWM External and Internal Interrupt Sources Programmable Watchdog Timer 6-MHz Oscillator with On-chip PLL 5V Operation with On-chip 3.3-V Power Supply 64-lead LQFP Package Multimedia USB Keyboard Controller with Embedded Hub AT43USB325 Description The Atmel AT43USB325 is an 8-bit microcontroller based on the AVR RISC architecture. By executing powerful instructions in a single clock cycle, the AT43USB325 achieves throughputs approaching 12 MIPS. The AVR core combines a rich instruction set with 32 general-purpose working registers. All 32 registers are directly connected to the ALU allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The AT43USB325 features an on-chip 16-Kbyte program memory and 512 bytes of data memory. It is supported by a standard set of peripherals such as timer/counter modules, watchdog timer and internal and external interrupt sources. The major peripheral included in the AT43USB325 is the USB Hub with an embedded function and GPIO ports designed for use in a keyboard controller. The embedded function has 4 endpoints that makes the AT43USB325 extremely suitable for keyboards supporting the consumer page as described in the "USB Usage Tables". The AT43USB325 comes in two versions. The program memory of the AT43USB325E is an SRAM that is automatically written from an external serial EEPROM during power on. The AT43USB325M has a masked ROM program memory. The two versions are pin, function and binary compatible. Rev. 3355A-USB-5/03 1 Pin Configuration Figure 1. 64-lead LQFP AT43USB325E-AC PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 Figure 2. 64-lead LQFP AT43USB325M-AC PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 2 AT43USB325 3355A-USB-5/03 RESETN TEST PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PD7 PD6 PD5 PD4 PF3 PF2 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PD3 PD1 PD0 DP0 DM0 DP2 DM2 DP3 DM3 VCC1 CEXT1 VSS1 DP4 DM4 DP5 DM5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 RESETN TEST PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PD7 PD6 PD5 PD4 MISO MOSI 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 PE0 PE1 PE2 PE3 LFT XTAL2 XTAL1 VSS2 CEXT2 VCC2 PE4 PE5 PE6 PE7 NC PF1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PD3 PD1 PD0 DP0 DM0 DP2 DM2 DP3 DM3 VCC1 CEXT1 VSS1 DP4 DM4 DP5 DM5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 PE0 PE1 PE2 PE3 LFT XTAL2 XTAL1 VSS2 CEXT2 VCC2 PE4 PE5 PE6 PE7 SSN SCK AT43USB325 Pin Assignment Pin# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Signal PD3 PD1 PD0 DP0 DM0 DP2 DM2 DP3 DM3 VCC1 CEXT1 VSS1 DP4 DM4 DP5 DM5 RESETN TEST PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PD7/INTD PD6/INTC PD5/INTB PD4/INTA PF3/SO/ICP PF2/SI/OC1B Type Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Power Supply/Ground Output Power Supply/Ground Bi-directional Bi-directional Bi-directional Bi-directional Input Input Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Pin# 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Signal PF1/SCK/OC1A NC/SSN PE7 PE6 PE5 PE4 VCC2 CEXT2 VSS2 XTAL1 XTAL2 LFT PE3 PE2 PE1 PE0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 Type Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Power Supply/Ground Output Power Supply/Ground Input Output Output Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional 3 3355A-USB-5/03 Signal Description Name VCC1, 2 CEXT1, 2 VSS1, 2 XTAL1 XTAL2 LFT Type Power Supply/Ground Output Power Supply/Ground Input Output Input Function 5V Power Supply External Capacitors for Internal Voltage Regulator - A high quality 2.2F capacitor must be connected to CEXT1 and 0.33 F to CEXT2 for proper operation of the chip. Ground Oscillator Input - Input to the inverting oscillator amplifier. Oscillator Output - Output of the inverting oscillator amplifier. PLL Filter - For proper operation of the PLL, this pin should be connected through a 0.01 F capacitor in parallel with a 100 resistor in series with a 0.1 F capacitor to ground (VSS). Both capacitors must be high quality ceramic. Upstream Plus USB I/O - This pin should be connected to CEXT1 through an external 1.5 k pull-up resistor. DP0 and DM0 form the differential signal pin pairs connected to the Host Controller or an upstream Hub. Upstream Minus USB I/O Port Plus USB I/O - Each of these pins should be connected to VSS through an external 15 k resistor. DP[2:5] and DM[2:5] are the differential signal pin pairs to connect downstream USB devices. Port Minus USB I/O - Each of these pins should be connected to VSS through an external 15 k resistor. Port A[0:7] - Bi-directional 8-bit I/O port with controlled slew rate. These pins are used as eight of the keyboard matrix column output strobes. PA[0:7] = COL[0:7]. Port B[0:7] - Bi-directional 8-bit I/O port controlled slew rate. These pins are used as the eight of the keyboard matrix column output strobes: PB[0:7] = COL[8:15]. PB0 has a dual function: the input to timer/counter0. PB[0:7] Bi-directional Port Pin PB0 PC[0:7] Bi-directional Alternate Function T0, Timer/Counter0 external input DPO DMO DP[2:5] Bi-directional Bi-directional Bi-directional DM[2:5] PA[0:7] Bi-directional Bi-directional Port C[0:7] - Bi-directional 8-bit I/O port with internal pull-ups. These pins are used as keyboard matrix row input signals. PC[0:7] = ROW [0:7]. Port D[0,1,3:7] - Bi-directional I/O ports. Port D[1,4:7] have dual functions as shown below: Port Pin Alternate Function PD1 T1, Timer/Counter1 External Input PD3 INT1, External Interrupt Input 1 PD4 INTA, External Interrupt Input A PD5 INTB, External Interrupt Input B PD6 INTC, External Interrupt Input C PD7 INTD, External Interrupt Input D Port E[0:3] - Bi-directional I/O port with controlled slew rate which can be used as four additional keyboard column output strobes, COL[16:19]. PE[4:7] - Bi-directional I/O port. PE[4:7] have built-in series limiting resistors and can be used to drive LEDs directly PD[0,1,3:7] Bi-directional PE[0:3] PE[4:7] Bi-directional Bi-directional 4 AT43USB325 3355A-USB-5/03 AT43USB325 Signal Description (Continued) Name Type Function Port F[1:3] - Bi-directional I/O port. In the AT43USB325E, these port pins have dual functions as the interface pins to the serial EEPROM as shown below: Alternate Function 1 (AT43USB325E only) SCK, SPI Master Clock Out SI, SPI Slave Data Input SO, SPI Slave Data Out PF[1:3] Bi-directional Port Pin PF1 PF2 PF3 Alternate Function 2 OC1A, Timer/Counter1 Output Compare A OC1B, Timer/Counter1 Output Compare B ICP, Timer/Counter1 Input Capture NC/SSN TEST RESETN Note: Output Input Input No Connect/Slave Select - In the AT43USB325M this pin is not used. In the AT43USB325E this pin is the SPI slave select input used for enabling the serial memory during program memory downloading. Test Pin - This pin should be tied to ground. Reset - Active low Signal names ending with an N are active low. 5 3355A-USB-5/03 Note: The AT43USB325 Enhanced RISC Architecture with USB Keyboard Controller and Hub 8 x 16 Program Memory Program Counter Status and Control Interrupt Unit Instruction Register 32 x 8 General-purpose Registers 8-bit Timer/Counter 16-bit Timer/Counter ALU Instruction Decoder Watchdog Timer Control Lines 512 x 8 SRAM 20 Strobe Outputs 8 Strobe Inputs 11 GPIO Lines 4 LED Drives USB Hub and Function 6 AT43USB325 3355A-USB-5/03 AT43USB325 Architectural Overview The AT43USB325 is a USB microcontroller with special peripherals for use as a programmable keyboard controller. The peripherals and features of the AT43USB325 microcontroller are similar to those of the AT90S8515, with the exception of the following modifications: * * * * * * * * A downloadable SRAM or masked ROM for program memory No EEPROM No external data memory accesses No analog comparator, SPI, UART Idle mode not supported Additional GPIO port pins: PE, PF Four new external interrupt input pins: INTA, INTB, INTC, INTD USB Hub with attached function The embedded USB hardware of the AT43USB325 is a compound device, consisting of a 5 port hub with a permanently attached function on one port. The hub and attached function are two independent USB devices, each having its own device addresses and control endpoints. The hub has its dedicated interrupt endpoint, while the USB function has three additional programmable endpoints with 8-byte FIFOs. The microcontroller always runs from a 12 MHz clock that is generated by the USB hardware. While the nominal and average period of this clock is 83.3 ns, it may have single cycles that deviate by 20.8 ns during a phase adjustment by the SIE's clock/data separator of the USB hardware. The microcontroller shares most of the control and status registers of the megaAVR Microcontroller Family. The registers for managing the USB operations are mapped into its SRAM space. The I/O section on page 16 summarizes the available I/O registers. The "AVR Register Set" on page 38 covers the AVR registers. Please refer to the Atmel AVR manual for more information. The fast-access register file contains 32 x 8-bit general-purpose working registers with a single clock cycle access time. This means that during one single clock cycle, one Arithmetic Logic Unit (ALU) operation is executed. Two operands are output from the register file, the operation is executed, and the result is stored back in the register file - in one clock cycle. Six of the 32 registers can be used as three 16-bit indirect address register pointers for Data Space addressing - enabling efficient address calculations. One of the three address pointers is also used as the address pointer for look-up tables in program memory. These added function registers are the 16-bit X-, Y- and Z-registers. The ALU supports arithmetic and logic operations between registers or between a constant and a register. Single register operations are also executed in the ALU. Figure Note: on page 6 shows the AT43USB325 AVR Enhanced RISC microcontroller architecture. In addition to the register operation, the conventional memory addressing modes can be used on the register file as well. This is enabled by the fact that the register file is assigned the 32 lowest Data Space addresses ($00 - $1 F), allowing them to be accessed as though they were ordinary memory locations. The I/O memory space contains 64 addresses for CPU peripheral functions as Control Registers, Timer/Counters, and other I/O functions. The I/O Memory can be accessed directly, or as the Data Space locations following those of the register file, $20 - $5F. The AVR uses a Harvard architecture concept - with separate memories and buses for program and data. The program memory is executed with a single-level pipelining. While one 7 3355A-USB-5/03 instruction is being executed, the next instruction is pre-fetched from the program memory. This concept enables instructions to be executed in every clock cycle. The program memory is a downloadable SRAM or a mask programmed ROM. With the relative jump and call instructions, the whole 24K address space is directly accessed. Most AVR instructions have a single 16-bit word format. Every program memory address contains a 16- or 32-bit instruction. During interrupts and subroutine calls, the return address Program Counter (PC) is stored on the stack. The stack is effectively allocated in the general data SRAM, and consequently, the stack size is only limited by the total SRAM size and the usage of the SRAM. All user programs must initialize the Stack Pointer (SP) in the reset routine (before subroutines or interrupts are executed). The 10-bit SP is read/write accessible in the I/O space. The 512-byte data SRAM can be easily accessed through the five different addressing modes supported in the AVR architecture. The memory spaces in the AVR architecture are all linear and regular memory maps. A flexible interrupt module has its control registers in the I/O space with an additional global interrupt enable bit in the status register. All interrupts have a separate interrupt vector in the interrupt vector table at the beginning of the program memory. The interrupts have priority in accordance with their interrupt vector position. The lower the interrupt vector address, the higher the priority. The Generalpurpose Register File Table 1. AVR CPU General-purpose Working Register Register R0 R1 R2 .. R13 R14 R15 R16 R17 .. R26 R27 R28 R29 R30 R31 $1A $1B $1C $1D $1E $1F X-register low byte X-register high byte Y-register low byte Y-register high byte Z-register low byte Z-register high byte $0D $0E $0F $10 $11 Address $00 $01 $02 Comment All register operating instructions in the instruction set have direct and single cycle access to all registers. The only exception is the five constant arithmetic and logic instructions SBCI, SUBI, CPI, ANDI, and ORI between a constant and a register, and the LDI instruction for load 8 AT43USB325 3355A-USB-5/03 AT43USB325 immediate constant data. These instructions apply to the second half of the registers in the register file - R16..R31. The general SBC, SUB, CP, AND, and OR and all other operations between two registers or on a single register apply to the entire register file. As shown in Table 1, each register is also assigned a data memory address, mapping them directly into the first 32 locations of the user Data Space. Although not being physically implemented as SRAM locations, this memory organization provides great flexibility in access of the registers, as the X-, Y-, and Z-registers can be set to index any register in the file. X-, Y- and ZRegisters Registers R26..R31 contain some added functions to their general-purpose usage. These registers are address pointers for indirect addressing of the Data Space. The three indirect address registers X, Y, and Z are defined as: X-register 15 7 XH 0 R27 ($1B) 7 XL 0 0 R26 ($1A) Y-register 15 7 YH 0 R29 ($1D) 7 YL 0 0 R28 ($1C) Z-register 15 7 ZH 0 R30 ($1F) 7 ZL 0 0 R31 ($1E) In the different addressing modes these address registers have functions as fixed displacement, automatic increment and decrement (see the descriptions for the different instructions). ALU - Arithmetic Logic Unit The high-performance AVR ALU operates in direct connection with all 32 general-purpose working registers. Within a single clock cycle, ALU operations between registers in the register file are executed. The ALU operations are divided into three main categories - arithmetic, logical and bit-functions. The AT43USB325E contains 16K bytes on-chip downloadable memory for program storage while the AT43USB325M has a masked programmable ROM. Since all instructions are 16- or 32-bit words, the program memory is organized as 8K x 16. The AT43USB325 Program Counter (PC) is 13 bits wide, thus addressing the 8,192 program memory addresses. Constant tables can be allocated within the entire program memory address space (see the LPM - Load Program Memory instruction description). The program memory of the AT43USB325E is automatically written with data stored in an external serial EEPROM during the chip's power on reset sequence. The power on reset is the only way the on-chip program memory of the AT43USB325E will be written or modified. Program Memory 9 3355A-USB-5/03 The two versions of the AT43USB325 are binary compatible. A firmware written for the AT43USB325E will work unaltered on the AT43USB325M. The only functional difference between the two versions is with respect to the serial EEPROM interface pins, GPIO PF[0:3]. The differences are: Port F Pins PF0 AT43USB325E Slave Select Pin - Its output will be asserted (low) during downloading of firmware and will stay de-asserted (high) after download is completed. Functions as serial EEPROM interface signals during downloading and as GPIO pins after download is completed. AT43USB325M NC (No connect) PF1, PF2, PF3 GPIO SPI Serial EEPROM Interface (AT43USB325E Only) The AT43USB325E is designed to interface directly with a synchronous serial peripheral interface (SPI) SEEPROM such as the Atmel AT25HP256/512. All instructions, addresses and data are transferred with the MSB first and start with a high-to-low SSN transition. Note: The SPI port of the AT43USB325E at PF[0:3] is dedicated for program memory downloading only. It cannot be accessed by the firmware program. Figure 3. AT43USB325E Read Sequence SSN MOSI AT43USB325E MISO SCK AT25HP256 Read Sequence 1. The AT43USB325E asserts its SSN output pin and outputs a 3 MHz clock at SCK. It continues to activate SCK until the completion of the read process. 2. The AT43USB325E transmits the READ op-code (= 0000011) through its MOSI, followed by the 16-bit byte address to be read, x0000. Please note that the AT43USB325E will send a 16-byte address only. SEEPROM with SPI that requires a 24-bit address cannot be used with the AT43USB325E. 3. The SEEPROM then shifts out the data through its MISO pin. 4. The AT43USB325E de-asserts SCK and SSN after 16K bytes data read is complete. Figure 4. READ Timing SSN 0 SCK 1 2 3 4 5 6 7 8 9 10 11 20 21 22 23 24 25 26 27 28 29 30 MOSI INSTRUCTION BYTE ADDRESS 15 14 13 ... 3 2 1 0 HIGH IMPEDANCE MISO 76 MSB 5 DATA OUT 4 3 2 1 0 10 AT43USB325 3355A-USB-5/03 AT43USB325 SRAM Data Memory Table 3 summarizes how the AT43USB325 SRAM Memory is organized. The lower 608 Data Memory locations address the Register file, the I/O Memory and the internal data SRAM. The first 96 locations address the Register File + I/O Memory, and the next 512 locations address the internal data SRAM. The five different addressing modes for the data memory cover: Direct, Indirect with Displacement, Indirect, Indirect with Pre-decrement and Indirect with Postincrement. In the register file, registers R26 to R31 feature the indirect addressing pointer registers. Direct addressing reaches the entire data space. The Indirect with Displacement mode features 63 address locations that reach from the base address given by the Y- or Z-register. When using register indirect addressing modes with automatic pre-decrement and post-increment, the address registers X, Y, and Z are decremented and incremented. The 32 general-purpose working registers, 64 I/O registers and the 512 bytes of internal data SRAM in the AT43USB325 are all accessible through these addressing modes. To manage the USB hardware, a special set of registers is assigned. These registers are mapped to SRAM space between addresses $1F00 and 1FFF. Table 3 and Table 4 give an overview of these registers. 11 3355A-USB-5/03 Table 2. SRAM Organization Register File R0 R1 Data Address Space $0000 $0001 R30 R31 I/O Registers $00 $01 $001E $001F $0020 $0021 $3E $3F $005E $005F Internal SRAM $0060 $0061 $025E $045F USB Registers $1F00 $1FFE $1FFF 12 AT43USB325 3355A-USB-5/03 AT43USB325 Table 3. USB Hub and Function Registers Address $1FFD $1FFC $1FFB $1FFA $1FF9 $1FF8 $1FF7 $1FF6 $1FF5 $1FF3 $1FF2 $1FEF $1FEE $1FE7 $1FE5 $1FE4 $1FE3 $1FE2 $1FDF $1FDD $1FDC $1FDB $1FDA $1FD7 $1FD5 $1FD4 $1FD3 $1FD2 $1FCF $1FCD $1FCC $1FCB $1FCA $1FC7 $1FC5 Name FRM_NUM_H FRM_NUM_L GLB_STATE SPRSR SPRSIE SPRSMSK UISR UIMSKR UIAR UIER UOVCER HADDR FADDR HENDP0_CNTR FENDP0_CNTR FENDP1_CNTR FENDP2_CNTR FENDP3_CNTR HCSR0 FCSR0 FCSR1 FCSR2 FCSR3 HDR0 FDR0 FDR1 FDR2 FDR3 HBYTE_CNT0 FBYTE_CNT0 FBYTE_CNT1 FBYTE_CNT2 FBYTE_CNT3 HSTR HPCON Function Frame Number High Register Frame Number Low Register Global State Register Suspend/Resume Register Suspend/Resume Interrupt Enable Register Suspend/Resume Interrupt Mask Register USB Interrupt Status Register USB Interrupt Mask Register USB Interrupt Acknowledge Register USB Interrupt Enable Register Overcurrent Detect Register Hub Address Register Function Address Register Hub Endpoint 0 Control Register Function Endpoint 0 Control Register Function Endpoint 1 Control Register Function Endpoint 2 Control Register Function Endpoint 3 Control Register Hub Controller Endpoint 0 Service Routine Register Function Controller Endpoint 0 Service Routine Register Function Controller Endpoint 1 Service Routine Register Function Controller Endpoint 2 Service Routine Register Function Controller Endpoint 3 Service Routine Register Hub Endpoint 0 FIFO Data Register Function Endpoint 0 FIFO Data Register Function Endpoint 1 FIFO Data Register Function Endpoint 2 FIFO Data Register Function Endpoint 3 FIFO Data Register Hub Endpoint 0 Byte Count Register Function Endpoint 0 Byte Count Register Function Endpoint 1 Byte Count Register Function Endpoint 2 Byte Count Register Function Endpoint 3 Byte Count Register Hub Status Register Hub Port Control Register 13 3355A-USB-5/03 Table 3. USB Hub and Function Registers (Continued) Address $1FBC $1FBB $1FBA $1FB9 $1FB8 $1FB4 $1FB3 $1FB2 $1FB1 $1FB0 $1FAC $1FAB $1FAA $1FA9 $1FA7 $1FA5 $1FA4 $1FA3 $1FA2 Name HPSTAT5 HPSTAT4 HPSTAT3 HPSTAT2 HPSTAT1 HPSCR5 HPSCR4 HPSCR3 HPSCR2 HPSCR1 PSTATE5 PSTATE4 PSTATE3 PSTATE2 HCAR0 FCAR0 FCAR1 FCAR2 FCAR3 Function Hub Port 5 Status Register Hub Port 4 Status Register Hub Port 3 Status Register Hub Port 2 Status Register Hub Port 1 Status Register Hub Port 5 Status Change Register Hub Port 4 Status Change Register Hub Port 3 Status Change Register Hub Port 2 Status Change Register Hub Port 1 Status Change Register Hub Port 5 Bus State Register Hub Port 4 Bus State Register Hub Port 3 Bus State Register Hub Port 2 Bus State Register Hub Endpoint 0 Control and Acknowledge Register Function Endpoint 0 Control and Acknowledge Register Function Endpoint 1 Control and Acknowledge Register Function Endpoint 2 Control and Acknowledge Register Function Endpoint 3 Control and Acknowledge Register 14 AT43USB325 3355A-USB-5/03 AT43USB325 Table 4. USB Hub and Function Registers Name GLB_STATE SPRSR SPRSIE SPRSMSK UISR UIMSKR UIAR UIER UOVCER ISCR HADDR FADDR HENDP0_CNTR FENDP0_CNTR FENDP1_CNTR FENDP2_CNTR FENDP3_CNTR HCSR0 FCSR0 FCSR1 FCSR2 FCSR3 HDR0 FDR0 FDR1 FDR2 FDR3 HBYTE_CNT0 FBYTE_CNT0 FBYTE_CNT1 FBYTE_CNT2 FBYTE_CNT3 HSTR HPCON HPSTAT5 HPSTAT4 HPSTAT3 HPSTAT2 HPSTAT1 HPSCR5 HPSCR4 HPSCR3 Address $1FFB $1FFA $1FF9 $1FF8 $1FF7 $1FF6 $1FF5 $1FF3 $1FF2 $1FF1 $1FEF $1FEE $1FE7 $1FE5 $1FE4 $1FE3 $1FE2 $1FDF $1FDD $1FDC $1FDB $1FDA $1FD7 $1FD5 $1FD4 $1FD3 $1FD2 $1FCF $1FCD $1FCC $1FCB $1FCA $1FC7 $1FC5 $1FBC $1FBB $1FBA $1FB9 $1FB8 $1FB4 $1FB3 $1FB2 Bit 7 - INTD INTD EN INTD MSK SOF INT SOF MSK SOF INTACK SOF IE - ISC71 SAEN FEN EPEN EPEN EPEN EPEN EPEN - - - - DATA7 DATA7 DATA7 DATA7 DATA7 - - - - - - - - - - Bit 6 KB INT EN INTC INTC EN INTC MSK EOF2 INT SOF2 MSK EOF2 INTACK EOF2 IE - ISC70 HADD6 FADD6 - - - - - - - - DATA6 DATA6 DATA6 DATA6 DATA6 - - - - - HPCON2 LSP LSP LSP LSP LSP - Bit 5 - INTB INTB EN INTB MSK - ISC61 HADD5 FADD5 - - - - - - - - DATA5 DATA5 DATA5 DATA5 DATA5 BYTCT5 BYTCT5 BYTCT5 BYTCT5 - HPCON1 PPSTAT PPSTAT PPSTAT PPSTAT PPSTAT - Bit 4 SUSP FLG INTA INTA EN INTA MSK FEP3 INT FEP3 MSK FEP3 INTACK FEP3 IE - ISC60 HADD4 FADD4 - - - - - - - - DATA4 DATA4 DATA4 DATA4 DATA4 BYTCT4 BYTCT4 BYTCT4 BYTCT4 BYTCT4 - HPCON0 PRSTAT PRSTAT PRSTAT PRSTAT PRSTAT RSTSC RSTSC RSTSC Bit 3 RESUME FLG HEP0 INT HEP0 MSK HEP0 INTACK HEP0 IE - ISC51 HADD3 FADD3 DTGLE DTGLE DTGLE DTGLE DTGLE STALL SENT STALL SENT STALL SENT STALL SENT STALL SENT DATA3 DATA3 DATA3 DATA3 DATA3 BYTCT3 BYTCT3 BYTCT3 BYTCT3 BYTCT3 OVLSC - POCI POCI POCI POCI POCI POCIC POCIC POCIC Bit 2 RMWUPE FRWUP FRWUP IE FRWUP MSK FEP2 INT FEP2 MSK FEP2 INTACK FEP2 IE OVC ISC50 HADD2 FADD2 EPDIR EPDIR EPDIR EPDIR EPDIR RX SETUP RX SETUP RX SETUP RX SETUP DATA2 DATA2 DATA2 DATA2 DATA2 BYTCT2 BYTCT2 BYTCT2 BYTCT2 BYTCT2 LPSC HPADD2 PSSTAT PSSTAT PSSTAT PSSTAT PSSTAT PSSC PSSC PSSC Bit 1 CONFG RSM RSM IE RSM MSK FEP1 INT FEP1 MSK FEP1 INTACK FEP1 IE - ISC41 HADD1 FADD1 EPTYPE1 EPTYPE1 EPTYPE1 EPTYPE1 EPTYPE1 RX OUT PACKET RX OUT PACKET RX OUT PACKET RX OUT PACKET RX OUT PACKET DATA1 DATA1 DATA1 DATA1 DATA1 BYTCT1 BYTCT1 BYTCT1 BYTCT1 BYTCT1 OVI HPADD1 PESTAT PESTAT PESTAT PESTAT PESTAT PESC PESC PESC Bit 0 HADD EN GLB SUSP GLB SUSP IE GLB SUSP MSK FEP0 INT FEP0 MSK FEP0 INTACK FEP0 IE - ISC40 HADD0 FADD0 EPTYPE0 EPTYPE0 EPTYPE0 EPTYPE0 EPTYPE0 TX CEMPLETE TX COMPLETE TX COMPLETE TX COMPLETE TX CMPLETE DATA0 DATA0 DATA0 DATA0 DATA0 BYTCT0 BYTCT0 BYTCT0 BYTCT0 BYTCT0 LPS HPADD0 PCSTAT PCSTAT PCSTAT PCSTAT PCSTAT PCSC PCSC PCSC 15 3355A-USB-5/03 Table 4. USB Hub and Function Registers (Continued) Name HPSCR2 HPSCR1 HCAR0 FCAR0 FCAR1 FCAR2 FCAR3 Address $1FB1 $1FB0 $1FA7 $1FA5 $1FA4 $1FA3 $1FA2 Bit 7 - - CTL DIR CTL DIR CTL DIR CTL DIR CTL DIR Bit 6 - - DATA END DATA END DATA END DATA END DATA END Bit 5 - - FORCE STALL FORCE STALL FORCE STALL FORCE STALL FORCE STALL Bit 4 RSTSC RSTSC TX PACKET READY TX PACKET READY TX PACKET READY TX PACKET READY TX PACK RDY Bit 3 POCIC POCIC STALL_SENT-ACK STALL_SENT-ACK STALL_SENT-ACK STALL_SENT-ACK STALL_SENT_ACK Bit 2 PSSC PSSC RX_SETUP_ACK RX_SETUP_ACK RX_SETUP_ACK RX_SETUP_ACK Bit 1 PESC PESC RX_OUT_PACKET_ACK RX_OUT_PACKET_ACK RX_OUT_PACKET_ACK RX_OUT_PACKET_ACK RX_OUT_PACKET_ACK Bit 0 PCSC PCSC TX_COMPLETE-ACK TX_COMPLETE-ACK TX_COMPLETE-ACK TX_COMPLETE-ACK TX_COMPLETE_ACK I/O Memory The I/O space definition of the AT43USB325 is shown in the following table: Table 5. I/O Memory Space I/O (SRAM) Address $3F ($5F) $3E ($5E) $3D ($5D) $3B ($5B) $3A ($5A) $39 ($59) $38 ($58) $35 ($55) $33 ($53) $32 ($52) $2F ($4F) $2E ($4E) $2D ($52) $2C ($52) $2B ($4B) $2A ($4A) $29 ($49) $28 ($48) $25 ($45) $24 ($44) $21 ($41) $1B ($4B) $1A ($3A) $19 ($39) Name SREG SPH SPL GIMSK GIFR TIMSK TIFR MCUCR TCCR0 TCNT0 TCCR1A TTCR1B TCNT1H TCNT1L OCR1AH OCR1AL OCR1BH OCR1BL ICR1H ICR1L WDTCR PORTA DDRA PINA Function Status Register Stack Pointer High Stack Pointer Low General Interrupt Mask Register General Interrupt Flag Register Timer/Counter Interrupt Mask Register Timer/Counter Interrupt Mask Register MCU General Control Register Timer/Counter0 Control Register Timer/Counter0 (8 bit) Timer/Counter1 Control Register A Timer/Counter1 Control Register B Timer/Counter1 High Byte Timer/Counter1 Low Byte Timer/Counter1 Output Compare Register A High Byte Timer/Counter1 Output Compare Register A Low Byte Timer/Counter1 Output Compare Register B High Byte Timer/Counter1 Output Compare Register B Low Byte T/C 1 Input Capture Register High Byte T/C 1 Input Capture Register Low Byte Watchdog Timer Counter Register Data Register, Port A Data Direction Register, Port A Input Pins, Port A 16 AT43USB325 3355A-USB-5/03 AT43USB325 Table 5. I/O Memory Space (Continued) I/O (SRAM) Address $18 ($38) $17 ($37) $16 ($36) $15 ($35) $14 ($34) $13 ($33) $12 ($32) $11 ($31) $10 ($30) $06 ($26) $05 ($25) $04 ($24) $03 ($23) $02 ($22) $01 ($21) Name PORTB DDRB PINB PORTC DDRC PINC PORTD DDRD PIND PORTF DDRF PINF PORTE DDRE PINE Function Data Register, Port B Data Direction Register, Port B Input Pins, Port B Data Register, Port C Data Direction Register, Port C Input Pins, Port C Data Register, Port D Data Direction Register, Port D Input Pins, Port D Data Register, Port F Data Direction Register, Port F Input Pins, Port F Data Register, Port E Data Direction Register, Port E Input Pins, Port E All AT43USB325 I/O and peripherals, except for the USB hardware registers, are placed in the I/O space. The I/O locations are accessed by the IN and OUT instructions transferring data between the 32 general-purpose working registers and the I/O space. I/O registers within the address range $00 - $1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of single bits can be checked by using the SBIS and SBIC instructions. Refer to the instruction set documentations of the AVR for more details. When using the I/O specific commands, IN and OUT, the I/O address $00 - $3F must be used. When addressing I/O registers as SRAM, $20 must be added to this address. All I/O register addresses throughout this document are shown with the SRAM address in parentheses. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. USB Hub A block diagram of the USB hardware of the AT43USB325 is shown in Figure 5. The USB hub of the AT43USB325 has 5 downstream ports. The embedded function is permanently attached to Port 1. Ports 2, 3, 4 and 5 are available as external ports. The actual number of ports used is strictly defined by the firmware of the AT43USB325 and can vary from 0 to 4. Because the exact configuration is defined by firmware, these ports may even function as permanently attached ports as long as the Hub Descriptor identifies them as such. The embedded USB function has its own device address and has a default endpoint plus 3 other programmable endpoints with their own 8-byte FIFOs. Endpoints 1 and 2 can be programmed as interrupt IN or OUT or bulk IN or OUT endpoints. USB Function 17 3355A-USB-5/03 Figure 5. USB Hardware Port 0 XCVR Port 2 XCVR Port 3 XCVR Hub Repeater Port 4 XCVR Port 5 XCVR Serial Interface Engine Hub Interface Unit Port 1 Function Interface Unit Data Address Control AVR Microcontroller 18 AT43USB325 3355A-USB-5/03 AT43USB325 Functional Description On-chip Power Supply The AT43USB325 contains two on-chip power supplies that generate 3.3V with a capacity of 30 mA each from the 5V power input. The on-chip power supplies are intended to supply the AT43USB325 internal circuit and the 1.5K pull-up resistor only and should not be used for other purposes. External 2.2 F filter capacitors are required at the power supply outputs, CEXT1 and CEXT2. The internal power supplies can be disabled as described in the next paragraph. The user should be careful when the GPIO pins are required to supply high-load currents. If the application requires that the GPIO supply currents beyond the capability of the on-chip power supply, the AT43USB325 should be supplied by an external 3.3V power supply. In this case, the 5V VCC power supply pin should be left unconnected and the 3.3V power supplied to the chip through the CEXT1 and CEXT2 pins. I/O Pin Characteristics The I/O pins of the AT43USB325 should not be directly connected to voltages less than VSS or more than the voltage at the CEXT pins. If it is necessary to violate this rule, insert a series resistor between the I/O pin and the source of the external signal source that limits the current into the I/O pin to less than 2 mA. Under no circumstance should the external voltage exceed 5.5V. To do so will put the chip under excessive stress. All clock signals required to operate the AT43USB325 are derived from an on-chip oscillator. To reduce EMI and power dissipation, the oscillator is designed to operate with a 6 MHz crystal. An on-chip PLL generates the high frequency for the clock/data separator of the Serial Interface Engine. In the suspended state, the oscillator circuitry is turned off. The oscillator of the AT43USB325 is a special, low-drive type, designed to work with most crystals without any external components. The crystal must be of the parallel resonance type requiring a load capacitance of about 10 pF. If the crystal requires a higher value capacitance, external capacitors can be added to the two terminals of the crystal and ground to meet the required value. To assure quick start-up, a crystal with a high Q, or low ESR, should be used. To meet the USB hub frequency accuracy and stability requirements for hubs, the crystal should have an accuracy and stability of better than 100 PPM. The use of a ceramic resonator in place of the crystal is not recommended because a resonator would not have the necessary frequency accuracy and stability. The clock can also be externally sourced. In this case, connect the clock source to the XTAL1 pin, while leaving XTAL2 pin floating. The switching level at the OSC1 pin can be as low as 0.47V and a CMOS device is required to drive this pin to maintain good noise margins at the low switching level. For proper operation of the PLL, an external RC filter consisting of a series RC network of 100 and 0.1 F in parallel with a 0.01 F capacitor must be connected from the LFT pin to VSS. Use only high-quality ceramic capacitors. Oscillator and PLL 19 3355A-USB-5/03 Figure 6. Oscillator and PLL U1 XTAL1 Y1 6.000 MHz XTAL2 AT43USB325 R1 100 LFT C1 0.22 UF C2 0.01 UF Reset and Interrupt Handling The AT43USB325 provides 12 different interrupt sources with 4 separate reset vectors, each with a separate program vector in the program memory space. Nine of the interrupt sources share 2 interrupt reset vectors. These nine are the USB related interrupts. All interrupts are assigned individual enable bits which must be set (one) together with the I-bit in the status register in order to enable the interrupt. The lowest addresses in the program memory space are automatically defined as the Reset and Interrupt vectors. The complete list of vectors is shown in Table 6. The list also determines the priority levels of the different interrupts. The lower the address, the higher is the priority level. RESET has the highest priority, and next is INT0 - the USB Suspend and Resume Interrupt, etc. Table 6. Reset and Interrupt Vectors Vector No. 1 2 3 4 5 6 7 8 13 Program Address $000 $002 $004 $006 $008 $00A $00C $00E $018 Source RESET INT0 INT1 TIMER1 CAPT TIMER1 COMPA TIMER1 COMPB TIMER1, OVF TIMER0, OVF USB HW Interrupt Definition External Reset, Power-on Reset and Watchdog Reset USB Suspend and Resume External Interrupt Request 1 Timer/Counter1 Capture Event Timer/Counter1 Compare Match A Timer/Counter1 Compare Match B Timer/Counter1 Overflow Timer/Counter0 Overflow USB Hardware 20 AT43USB325 3355A-USB-5/03 AT43USB325 The most typical and general program setup for the Reset and Interrupt Vector Addresses are: Address $000 $002 $00E Overflow Handler $018 ; $00d start $00e $00f $010 $011 out SPH, r16 ldi r16, low (RAMEND) out SPL, r16 ... ... ... ... USB related interrupt events are routed to reset vectors 13 and 2 through a separate set of interrupt, interrupt enable and interrupt mask registers that are mapped to the data SRAM space. These interrupts must be enabled though their control register bits. In the event an interrupt is generated, the source of the interrupt is identified by reading the interrupt registers. The USB frame and transaction related interrupt events, such as Start of Frame interrupt, are grouped in one set of registers: USB Interrupt Flag Register, USB Interrupt Enable Register and USB Interrupt Mask Register. The USB Bus reset and suspend/resume are grouped in another set of registers: Suspend/Resume Register, Suspend/Resume Interrupt Enable Register and Suspend/Resume Interrupt Mask Register. Some applications may include firmware routines lasting for long periods that can not be interrupted. At the same time, other less critical events may need attention after the critical routine is completed. The AT43USB325 solves this problem by having interrupt mask registers in addition to the interrupt enable registers of the USB related interrupts. The difference between the mask and enable registers is: * * The enable register enables the interrupt so it is captured into the interrupt register. If it is not enabled, and an interrupt occurs, the interrupt will be lost. The mask register merely masks the interrupt from interrupting the CPU. Upon unmasking, the pending interrupt is triggered. 21 3355A-USB-5/03 Figure 7. AT43USB325 Interrupt Structure USB Interrupt Flag Register SOF USB EOF2 FEP3 FEP2 FEP1 FEP0 HEP0 13 USB Interrupt Enable Register USB Interrupt Mask Register Microcontroller Interrupt Logic TIMER0 OVF TIMER OVF COMPB COMPA Suspend/Resume Interrupt Enable Register Suspend/Resume Interrupt Mask Register INT1 INT0 RESET 8 7 6 5 Suspend/Resume Register FRMWUP RSM GLB SUSP BUS RESET INTA INTB INTC INTD 3 2 1 Reset Sources The AT43USB325 has four sources of reset: * * * * Power-on Reset - The MCU is reset when the supply voltage is below the power-on reset threshold. External Reset - The MCU is reset when a low level is present on the RESET pin for more than 50 ns. Watchdog Reset - The MCU is reset when the watchdog timer period expires and the watchdog is enabled. USB Reset - The AT43USB325 has a feature to separate the USB and microcontroller resets. This feature is enabled by setting the BUS INT EN, bit 3 of the SPRSIE register. A USB bus reset is defined as a SE0 (single ended zero) of at least 4 slow speed USB clock cycles received by Port0. The internal reset pulse to the USB hardware and microcontroller lasts for 24 oscillator periods. - - Resets not separated: A USB bus reset will also reset the microcontroller. Separated reset: A USB bus reset will only reset the USB hardware, while an interrupt to the microcontroller will be generated if the BUS INT MSK bit, bit 3 of SPRSMSK register, is also set. 22 AT43USB325 3355A-USB-5/03 AT43USB325 When the USB hardware is reset, the compound device is de-configured and has to be reenumerated by the host. When the microcontroller is reset, all I/O registers are then set to their initial values, and the program starts execution from address $000. The instruction placed in address $000 must be a JMP instruction to the reset handling routine. If the program never enables an interrupt source, the interrupt vectors are not used, and regular program code can be placed at these locations. The circuit diagram in Figure 8 shows the reset logic. Figure 8. Reset Logic USB Reset VCC POR Ckt OR RSTN Reset Ckt S ON Cntr Reset Watchdog Timer FSTRT 1-MHz Clock Divider 14-bit Cntr R Power-on Reset A Power-on Reset (POR) circuit ensures that the device is reset from power-on. An internal timer clocked from the Watchdog timer oscillator prevents the MCU from starting until after a certain period after VCC has reached the power-on threshold voltage, regardless of the VCC rise time. If the build-in start-up delay is sufficient, RESET can be connected to VCC directly or via an external pull-up resistor. By holding the pin low for a period after VCC has been applied, the Power-on Reset period can be extended. External Reset An external reset is generated by a low-level on the RESET pin. Reset pulses longer than 200 ns will generate a reset. Shorter pulses are not guaranteed to generate a reset. When the applied signal reaches the Reset Threshold Voltage - VRST on its positive edge, the delay timer starts the MCU after the Time-out period tTOUT has expired. Figure 9. External Reset During Operation VCC RESET VRST tTOUT TIME-OUT INTERNAL RESET 23 3355A-USB-5/03 Watchdog Timer Reset When the watchdog times out, it will generate a short reset pulse of 1 XTAL cycle duration. On the falling edge of this pulse, the delay timer starts counting the Time-out period tTOUT. Figure 10. Watchdog Reset During Operation VCC RESET 1 XTAL Cycle WDT TIME-OUT tTOUT RESET TIME-OUT INTERNAL RESET Non-USB Related Interrupt Handling The AT43USB325 has two non-USB 8-bit Interrupt Mask control registers; GIMSK (General Interrupt Mask Register) and TIMSK (Timer/Counter Interrupt Mask Register). When an interrupt occurs, the Global Interrupt Enable I-bit is cleared (zero) and all interrupts are disabled. The user software can set (one) the I-bit to enable nested interrupts. The I-bit is set (one) when a Return from Interrupt instruction, RETI, is executed. For Interrupts triggered by events that can remain static (e.g. the Output Compare register1 matching the value of Timer/Counter1) the interrupt flag is set when the event occurs. If the interrupt flag is cleared and the interrupt condition persists, the flag will not be set until the event occurs the next time. When the Program Counter is vectored to the actual interrupt vector in order to execute the interrupt handling routine, hard-ware clears the corresponding flag that generated the interrupt. Some of the interrupt flags can also be cleared by writing a logic one to the flag bit position(s) to be cleared. If an interrupt condition occurs when the corresponding interrupt enable bit is cleared (zero), the interrupt flag will be set and remembered until the interrupt is enabled, or the flag is cleared by software. If one or more interrupt conditions occur when the global interrupt enable bit is cleared (zero), the corresponding interrupt flag(s) will be set and remembered until the global interrupt enable bit is set (one), and will be executed by order of priority. Note that external level interrupt does not have a flag, and will only be remembered for as long as the interrupt condition is active. 24 AT43USB325 3355A-USB-5/03 AT43USB325 General Interrupt Mask Register - GIMSK Bit 7 INT1 R/W 0 6 INT0 R/W 0 5 - R 0 4 - R 0 3 - R 0 2 - R 0 1 - R 0 0 - R 0 GIMSK $3B ($5B) Read/Write Initial Value * Bit 7 - INT1: External Interrupt Request 1 Enable When the INT1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the external pin interrupt is enabled. The Interrupt Sense Control1 bits 1/0 (ISC11 and ISC10) in the MCU general Control Register (MCUCR) defines whether the external interrupt is activated on rising or falling edge of the INT1 pin or level sensed. Activity on the pin will cause an interrupt request even if INT1 is configured as an output. The corresponding interrupt of External Interrupt Request 1 is executed from program memory address $004. See also "External Interrupts" on page 28. * Bit 6 - INT0: Interrupt Request 0 (Suspend/Resume Interrupt) Enable When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the external pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the MCU general Control Register (MCUCR) defines whether the external interrupt is activated on rising or falling edge of the INT0 pin or level sensed. Activity on the pin will cause an interrupt request even if INT0 is configured as an output. The corresponding interrupt of Interrupt Request 0 is executed from program memory address $002. See also "External Interrupts" on page 28. * Bits 5..0 - Res: Reserved Bits These bits are reserved bits in the AT43USB325 and always read as zero. General Interrupt Flag Register - GIFR Bit $3A ($5A) Read/Write Initial Value 7 INTF1 R/W 0 6 INT F0 R/W 0 5 - R 0 4 - R 0 3 - R 0 2 - R 0 1 - R 0 0 - R 0 GIFR * Bit 7 - INTF1: External Interrupt Flag1 When an event on the INT1 pin triggers an interrupt request, INTF1 becomes set (one). If the I-bit in SREG and the INT1 bit in GIMSK are set (one), the MCU will jump to the interrupt vector at address $004. The flag is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it. * Bit 6 - INTF0: Interrupt Flag0 (Suspend/Resume Interrupt Flag) When an event on the INT0 (that is, a USB event-related interrupt) triggers an interrupt request, INTF0 becomes set (one). If the I-bit in SREG and the INT0 bit in GIMSK are set (one), the MCU will jump to the interrupt vector at address $002. The flag is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it. * Bits 5..0 - Res: Reserved Bits These bits are reserved bits in the AT43USB325 and always read as zero. 25 3355A-USB-5/03 Timer/Counter Interrupt Mask Register - TIMSK Bit $39 ($59) Read/Write Initial Value 7 TOIE1 R/W 0 6 OCIE1A R/W 0 5 OCIE1NB R/W 0 4 - R 0 3 TICIE1 R/W 0 2 - R 0 1 TOIE0 R/W 0 0 - R 0 TIMSK * Bit 7 - TOIE1: Timer/Counter1 Overflow Interrupt Enable When the TOIE1 bit is set (one) and the I-bit in the Status Register is set (one), the Timer/Counter1 Overflow interrupt is enabled. The corresponding interrupt (at vector $006) is executed if an overflow in Timer/Counter1 occurs, i.e., when the TOV1 bit is set in the Timer/Counter Interrupt Flag Register (TIFR). * Bit 6 - OCE1A: Timer/Counter1 Output CompareA Match Interrupt Enable When the OCIE1A bit is set (one) and the I-bit in the Status Register is set (one), the Timer/Counter1 CompareA Match interrupt is enabled. The corresponding interrupt (at vector $004) is executed if a CompareA match in Timer/Counter1 occurs, i.e., when the OCF1A bit is set in the TIFR. * Bit 5 - OCIE1B: Timer/Counter1 Output CompareB Match Interrupt Enable When the OCIE1B bit is set (one) and the I-bit in the Status Register is set (one), the Timer/Counter1 CompareB Match interrupt is enabled. The corresponding interrupt (at vector $005) is executed if a CompareB match in Timer/Counter1 occurs, i.e., when the OCF1B bit is set in the TIFR. * Bit 4 - Res: Reserved Bit This bit is a reserved bit in the AT43USB325 and always reads zero. * Bit 3 - TICIE1: Timer/Counter1 Input Capture Interrupt Enable When the TICIE1 bit is set (one) and the I-bit in the Status Register is set (one), the Timer/Counter1 Input Capture Event Interrupt is enabled. The corresponding interrupt (at vector $003) is executed if a capture-triggering event occurs on pin 31, ICP, i.e., when the ICF1 bit is set in the TIFR. * Bit 2 - Res: Reserved Bit This bit is a reserved bit in the AT43USB325 and always reads zero. * Bit 1 - TOIE0: Timer/Counter0 Overflow Interrupt Enable When the TOIE0 bit is set (one) and the I-bit in the Status Register is set (one), the Timer/Counter0 Overflow interrupt is enabled. The corresponding interrupt (at vector $007) is executed if an overflow in Timer/Counter0 occurs, i.e., when the TOV0 bit is set in the TIFR. * Bit 0 - Res: Reserved Bit This bit is a reserved bit in the AT43USB325 and always reads zero. 26 AT43USB325 3355A-USB-5/03 AT43USB325 Timer/Counter Interrupt Flag Register - TIFR Bit $38 ($58) Read/Write Initial Value 7 TOV1 R/W 0 6 OCF1A R/W 0 5 OCIFB R/W 0 4 - R 0 3 ICF1 R/W 0 2 - R 0 1 TOV0 R/W 0 0 - R 0 TIFR * Bit 7 - TOV1: Timer/Counter1 Overflow Flag The TOV1 is set (one) when an overflow occurs in Timer/Counter1. TOV1 is cleared by the hardware when executing the corresponding interrupt handling vector. Alternatively, TOV1 is cleared by writing a logic one to the flag. When the I-bit in SREG, and TOIE1 (Timer/Counter1 Overflow Interrupt Enable), and TOV1 are set (one), the Timer/Counter1 Overflow Interrupt is executed. In PWM mode, this bit is set when Timer/Counter1 changes counting direction at $0000. * Bit 6 - OCF1A: Output Compare Flag 1A The OCF1A bit is set (one) when compare match occurs between the Timer/Counter1 and the data in OCR1A - Output Compare Register 1A. OCF1A is cleared by the hardware when executing the corresponding interrupt handling vector. Alternatively, OCF1A is cleared by writing a logic one to the flag. When the I-bit in SREG, and OCIE1A (Timer/Counter1 Compare match InterruptA Enable), and the OCF1A are set (one), the Timer/Counter1 Compare A match Interrupt is executed. * Bit 5 - OCF1B: Output Compare Flag 1B The OCF1B bit is set (one) when compare match occurs between the Timer/Counter1 and the data in OCR1B - Output Compare Register 1B. OCF1B is cleared by the hardware when executing the corresponding interrupt handling vector. Alternatively, OCF1B is cleared by writing a logic one to the flag. When the I-bit in SREG, and OCIE1B (Timer/Counter1 Compare match InterruptB Enable), and the OCF1B are set (one), the Timer/Counter1 Compare B match Interrupt is executed. * Bit 4 - Res: Reserved Bit This bit is a reserved bit in the AT43USB325 and always reads zero. * Bit 3 - ICF1: - Input Capture Flag 1 The ICF1 bit is set (one) to flag an input capture event, indicating that the Timer/Counter1 value has been transferred to the input capture register - ICR1. ICF1 is cleared by the hardware when executing the corresponding interrupt handling vector. Alternatively, ICF1 is cleared by writing a logic one to the flag. When the SREG I-bit, and TICIE1 (Timer/Counter1 Input Capture Interrupt Enable), and ICF1 are set (one), the Timer/Counter1 Capture Interrupt is executed. * Bit 2 - Res: Reserved Bit This bit is a reserved bit in the AT43USB325 and always reads zero. * Bit 1 - TOV: Timer/Counter0 Overflow Flag The bit TOV0 is set (one) when an overflow occurs in Timer/Counter0. TOV0 is cleared by the hardware when executing the corresponding interrupt handling vector. Alternatively, TOV0 is cleared by writing a logic one to the flag. When the SREG I- bit, and TOIE0 (Timer/Counter0 Overflow Interrupt Enable), and TOV0 are set (one), the Timer/Counter0 Overflow interrupt is executed. * Bit 0 - Res: Reserved Bit This bit is a reserved bit in the AT43USB325 and always reads zero. 27 3355A-USB-5/03 External Interrupts The external interrupts are triggered by the INT1 and INTA/B/C/D pins. Observe that, if enabled, the INT1 interrupt will trigger even if the INT1 pin is configured as an output. This feature provides a way of generating a software interrupt. A falling or rising edge or a low level can trigger the external interrupts. This is set up as indicated in the specification for the MCU Control Register - MCUCR and the Interrupt Sense Control Register - ISCR. When INT1 is enabled and is configured as level triggered, the interrupt will trigger as long as the pin is held low. INT1 is set up as described in the specification for the MCU Control Register - MCUCR. The interrupt execution response for all the enabled AVR interrupts is 4 clock cycles minimum. 4 clock cycles after the interrupt flag has been set, the program vector address for the actual interrupt handling routine is executed. During this 4 clock cycle period, the Program Counter (2 bytes) is pushed onto the Stack, and the Stack Pointer is decremented by 2. The vector is normally a jump to the interrupt routine, and this jump takes 3 clock cycles. If an interrupt occurs during execution of a multi-cycle instruction, this instruction is completed before the interrupt is served. A return from an interrupt handling routine (same as for a subroutine call routine) takes 4 clock cycles. During these 4 clock cycles, the Program Counter (2 bytes) is popped back from the Stack, the Stack Pointer is incremented by 2, and the I flag in SREG is set. When the AVR exits from an interrupt, it will always return to the main program and execute one more instruction before any pending interrupt is served. Interrupt Response Time 28 AT43USB325 3355A-USB-5/03 AT43USB325 MCU Control Register - MCUCR Bit $35 ($55) Read/Write Initial Value 7 - R 0 6 - R 0 5 SE R/W 0 4 SM R/W 0 3 ISC11 R/W 0 2 ISC10 R/W 0 1 - R 0 0 - R 0 MCUCR * Bit 7, 6 - Res: Reserved Bits * Bit 5 - SE: Sleep Enable The SE bit must be set (1) to make the MCU enter the sleep mode when the SLEEP instruction is executed. To avoid the MCU entering the sleep mode, unless it is the programmer's purpose, it is recommended to set the Sleep Enable SE bit just before the execution of the SLEEP instruction. * Bit 4 - SM: Sleep Mode This bit selects between the two available sleep modes. When SM is cleared (zero), Idle Mode is selected as Sleep Mode. When SM is set (1), Power Down mode is selected as sleep mode. The AT43USB325 does not support the Idle Mode and SM should always be set to one when entering the Sleep Mode. * Bit 3, 2 - ISC11, ISC10: Interrupt Sense Control 1 Bit 1 and Bit 0 The External Interrupt 1 is activated by the external pin INT1 if the SREG I-flag and the corresponding interrupt mask in the GIMSK is set. The level and edges on the external INT1 pin that activate the interrupt are defined in the following table: Table 7. INT1 Sense Control ISC11 0 0 1 1 ISC10 0 1 0 1 Description The low level of INT1 generates an interrupt request. Reserved. The falling edge of INT1 generates an interrupt request. The rising edge of INT1 generates an interrupt request. 29 3355A-USB-5/03 USB Interrupt Sources The USB interrupts are described below. Table 8. USB Interrupt Sources Interrupt SOF Received EOF2 Function EP0 Interrupt Function EP1 Interrupt Description Whenever USB hardware decodes a valid Start of Frame. The frame number is stored in the two Frame Number Registers. Activated whenever the hub's frame timer reaches its EOF2 time point. See "Control Transfers at Control End-point EP0" on page 63 for details. For an OUT endpoint it indicates that Function Endpoint 1 has received a valid OUT packet and that the data is in the FIFO. For an IN endpoint it means that the endpoint has received an IN token, sent out the data in the FIFO and received an ACK from the Host. The FIFO is now ready to be written by new data from the microcontroller. For an OUT endpoint it indicates that Function Endpoint 2 has received a valid OUT packet and that the data is in the FIFO. For an IN endpoint it means that the endpoint has received an IN token, sent out the data in the FIFO and received an ACK from the Host. The FIFO is now ready to be written by new data from the microcontroller. For an OUT end-point it indicates that Function End-point 3 has received a valid OUT packet and that the data is in the FIFO. For an IN end-point it means that the end-point has received an IN token, sent out the data in the FIFO and received an ACK from the Host. The FIFO is now ready to be written by new data from the microcontroller. See "Control Transfers at Control End-point EP0" on page 63 for details. USB hardware has received a embedded function remote wakeup request. USB hardware has received global suspend signaling and is preparing to put the hub in the suspend mode. The microcontroller's firmware should place the embedded function in the suspend state. USB hardware received resume signaling and is propagating the resume signaling. The microcontroller's firmware should take the embedded function out of the suspended state. USB hardware received a USB bus reset. This applies only in cases where a separation between USB bus reset and microcontroller reset is required. Be very careful when using this feature. Function EP2 Interrupt Function EP3 Interrupt Hub EP0 Interrupt FRWUP GLB SUSP RSM BUS RESET All interrupts have individual enable, status, and mask bits through the interrupt enable register and interrupt mask register. The Suspend and Resume interrupts are cleared by writing a 0 to the particular interrupt bit. All other interrupts are cleared when the microcontroller sets a bit in an interrupt acknowledge register. 30 AT43USB325 3355A-USB-5/03 AT43USB325 USB Endpoint Interrupt Sources An assertion or activation of one or more bits in the endpoint's Control and Status Register triggers the endpoint interrupts. These triggers are different for control and non-control endpoints as described in the table below. Please refer to the Control and Status Register for more information. Table 9. USB Endpoint Interrupt Sources Bit RX_OUT_PACKET TX_COMPLETE STALL_SENT RX_SETUP Endpoint type CONTROL, OUT CONTROL, IN CONTROL, IN CONTROL USB Interrupt Status Register - UISR Bit $1FF7 Read/Write Initial Value 7 SOF INT R 0 6 EOF2 INT R 0 5 - R 0 4 FE3 INT R 0 3 HEP0 INT R 0 2 FE2 INT R 0 1 FE1 INT R 0 0 FE0 INT R 0 UISR * Bit 7 - SOF INT: Start of Frame Interrupt This bit is asserted after the USB hardware receives a valid SOF packet. * Bit 6 - EOF2 INT: EOF2 Interrupt This bit is asserted 10 clocks before the expected start of a frame. * Bit 5 - Res: Reserved Bit This bit is reserved and always reads as zero. * Bit 4 - FEP3 INT: Function End-point 3 Interrupt * Bit 3 - HEP0 INT: Hub Endpoint 0 Interrupt * Bit 2 - FEP2 INT: Function Endpoint 2 Interrupt * Bit 1 - FEP1 INT: Function Endpoint 1 Interrupt * Bit 0 - FEP0 INT: Function Endpoint 0 Interrupt The hub and function interrupt bits will be set by the hardware whenever the following bits in the corresponding endpoint's Control and Status Register are modified by the USB hardware: 1. RX OUT Packet is set (control and OUT endpoints) 2. TX Packet Ready is cleared AND TX Complete is set (control and IN endpoints) 3. RX SETUP is set (control endpoints only) 4. TX Complete is set 31 3355A-USB-5/03 USB Interrupt Mask Register - UIMSKR Bit $1FF6 Read/Write Initial Value 7 SOF IMSK R/W 0 6 EOF2 IMSK R/W 0 5 - R 0 4 FEP3 IMSK R/W 0 3 HEP0 IMSK R/W 0 2 FEP2 IMSK R/W 0 1 FEP1 IMSK R/W 0 0 FEP0 IMSK R/W 0 UIMSKR * Bit 7 - SOF IMSK: Enable Start of Frame Interrupt Mask When the SOF IMSK bit is set (1), the Start of Frame Interrupt is masked. * Bit 6 - EOF2 IMSK: Enable EOF2 Interrupt When the EOF2 IMSK bit is set (1), the EOF2 Interrupt is masked. * Bit 5 - Res: Reserved Bit This bit is reserved and always read as zero. * Bit 4 - FEP3 IMSK: Function End-point 3 Interrupt Mask When the FE3 IMSK bit is set (1), the Function End-point 3 Interrupt is masked. * Bit 3 - HEP0 IMSK: Enable Endpoint 0 Interrupt When the HEP0 IMSK bit is set (1), the Hub Endpoint 0 Interrupt is masked. * Bit 2 - FEP2 IMSK: Enable Endpoint 2 Interrupt When the FE2 IMSK bit is set (1), the Function Endpoint 2 Interrupt is masked. * Bit 1 - FEP1 IMSK: Enable Endpoint 1 Interrupt When the FE1 IMSK bit is set (1), the Function Endpoint 1 Interrupt is masked. * Bit 0 - FEP0 IMSK: Enable Endpoint 0 Interrupt When the FE0 IMSK bit is set (1), the Function Endpoint 0 Interrupt is masked. 32 AT43USB325 3355A-USB-5/03 AT43USB325 USB Interrupt Acknowledge Register - UIAR Bit $1FF5 Read/Write Initial Value 7 SOF INTACK W 0 6 EOF2 INTACK W 0 5 - R 0 4 FEP3 INTACK W 0 3 HEP0 INTACK W 0 2 FEP2 IMSK W 0 1 FEP1 INTACK W 0 0 FEP0 INTACK W 0 UIAR * Bit 7 - SOF INTACK: Start of Frame Interrupt Acknowledge The microcontroller firmware writes a 1 to this bit to clear the SOF INT bit. * Bit 6 - EOF2 INTACK: EOF2 Interrupt Acknowledge The microcontroller firmware writes a 1 to this bit to clear the EOF2 INT bit. * Bit 5 - Res: Reserved bit This bit is reserved and is always read as zero. * Bit 4 - FEP3 INTACK: Function End-point 3 Interrupt Acknowledge The microcontroller firmware writes a 1 to this bit to clear the FEP3 INT bit. * Bit 3 - HEP0 INTACK: Hub Endpoint 0 Interrupt Acknowledge The microcontroller firmware writes a 1 to this bit to clear the HEP0 INT bit. * Bit 2 - FEP2 INTACK: Function Endpoint 2 Interrupt Acknowledge The microcontroller firmware writes a 1 to this bit to clear the FEP2 bit. * Bit 1 - FEP1 INTACK: Function Endpoint 1 Interrupt Acknowledge The microcontroller firmware writes a 1 to this bit to clear the FEP1 bit. * Bit 0 - FEP0 INTACK: Function Endpoint 0 Interrupt Acknowledge The microcontroller firmware writes a 1 to this bit to clear the FEP0 INT bit. 33 3355A-USB-5/03 USB Interrupt Enable Register - UIER Bit $1FF3 Read/Write Initial Value 7 SOF IE R/W 0 6 EOF2 IE R/W 0 5 - R 0 4 FEP3 IE R/W 0 3 HEP0 IE R/W 0 2 FEP2 IE R/W 0 1 FEP1 IE R/W 0 0 FEP0 IE R/W 0 UIER * Bit 7 - SOF IE: Enable Start of Frame Interrupt When the SOF IE bit is set (1), the Start of Frame Interrupt is enabled. * Bit 6 - EOF2 IE: Enable EOF2 Interrupt When the EOF2 IE bit is set (1), the EOF2 Interrupt is enabled. * Bit 5 - Res: Reserved bit This bit is reserved and always read as zero. * Bit 4 - FEP3 IE: Enable Function End-point 3 Interrupt When the FE3 IE bit is set (1), the Function End-point 3 Interrupt is enabled. * Bit 3 - HEP0 IE: Enable Endpoint 0 Interrupt When the HEP0 IE bit is set (1), the Hub Endpoint 0 Interrupt is enabled. * Bit 2 - FEP2 IE: Enable Endpoint 2 Interrupt When the FE2 IE bit is set (1), the Function Endpoint 2 Interrupt is enabled. * Bit 1 - FEP1 IE: Enable Endpoint 1 Interrupt When the FE1 IE bit is set (1), the Function Endpoint 1 Interrupt is enabled. * Bit 0 - FEP0 IE: Enable Endpoint 0 Interrupt When the FE0 IE bit is set (1), the Function Endpoint 0 Interrupt is enabled. Suspend/Resume Register - SPRSR Bit $1FFA Read/Write Initial Value 7 INTD R 0 6 INTC R 0 5 INTB R 0 4 INTA R 0 3 BUS INT R/W 0 2 FRWUP R 0 1 RSM R 0 0 GLB SUSP R 0 SPRSR * Bit 7 - INTD: External Interrupt D The INTD bit is set when an external interrupt at the INTD pin is detected. * Bit 6 - INTC: External Interrupt C The INTC bit is set when an external interrupt at the INTC pin is detected. * Bit 5 - INTB: External Interrupt B The INTB bit is set when an external interrupt at the INTB pin is detected. * Bit 4 - INTA: External Interrupt A The INTA bit is set when an external interrupt at the INTA pin is detected. Note: INTA/B/C/D cannot be used to wake up the AT43USB325 from the suspend state. * Bit 3 - BUS INT: USB Bus Interrupt When the USB reset separation feature is enabled (= SPRSIE and SPRSMSK bits 3 are set to 1) the BUS INT bit is set when USB bus reset is detected by the USB hardware. 34 AT43USB325 3355A-USB-5/03 AT43USB325 * Bit 2 - FRWUP: Function Remote Wakeup The USB hardware sets this bit to signal that a key depression is detected indicating remote wakeup. An interrupt is generated if the FRWUP IE bit of the SPRSIE register is set. * Bit 1 - RSM: Resume The USB hardware sets this bit when a USB resume signaling is detected at any of its port except Port 1. An interrupt is generated if the RSM IE bit of the SPRSIE register is set. * Bit 0 - GLB SUSP: Global Suspend The USB hardware sets this bit when a USB global suspend signaling is detected. An interrupt is generated if the GLBSUSP IE bit of the SPRSIE register is set. Suspend/Resume Interrupt Enable Register - SPRSIE Bit 7 INTD EN R/W 0 6 INTC EN R/W 0 5 INTB EN R/W 0 4 INTA EN R/W 0 3 BUS INT EN R/W 0 2 FRWUP IE R/W 0 1 RSM IE R/W 0 0 GLB SUSP IE R/W 0 SPRSIE $1FF9 Read/Write Initial Value * * Bit 7 - INTD EN: External Interrupt D Enable Setting the INTD EN bit will initiate an interrupt whenever the INTD bit of SPRSR is set. * * Bit 6 - INTC EN: External Interrupt C Enable Setting the INTC EN bit will initiate an interrupt whenever the INTC bit of SPRSR is set. * * Bit 5 - INTB EN: External Interrupt B Enable Setting the INTD EN bit will initiate an interrupt whenever the INTB bit of SPRSR is set. * * Bit 4 - INTA EN: External Interrupt A Enable Setting the INTD EN bit will initiate an interrupt whenever the INTA bit of SPRSR is set. * * Bit 3 - BUS INT EN: USB Reset Interrupt Enable When the BUS INT EN bit is set, the USB and C resets are separated. A USB bus reset (SE0 for longer than 3 ms) will reset the USB hardware only and not the C. However, an interrupt to the C will be generated and bit 3 of SPRSR is set. * * Bit 2 - FRWUP IE: Function Remote Wakeup Interrupt Enable Setting the FRWUP IE bit will initiate an interrupt whenever the FRWUP bit of SPRSR is set. * * Bit 1 - RSM IE: Resume Interrupt Enable Setting the RSM IE bit will initiate an interrupt whenever the RSM bit of SPRSR is set. * * Bit 0 - GLB SUSP IE: Global Suspend Interrupt Enable Setting the GLB SUSP IE bit will initiate an interrupt whenever the GLB SUSP bit of SPRSR is set. 35 3355A-USB-5/03 Suspend/Resume Interrupt Mask Register - SPRSMSK Bit $1FF8 Read/Write Initial Value 7 INTD MSK 6 INTC MSK 5 INTB MSK 4 INTA MSK 3 BUS INT MSK 2 FRWUP MSK 1 RSM MSK 0 GLB SUSP MSK SPRSMSK W 0 W 0 W 0 W 0 W 0 W 0 W 0 W 0 The bits of the Suspend/Resume Mask Register are used to make an interrupt caused by an event in the Suspend/Resume Register visible to the C. The Suspend/Resume Interrupt Enable Register bits enables the interrupt while the Suspend/Resume Interrupt Mask Register allows the C to control when it wants visibility to an interrupt. 1 = enable mask, 0 = disable mask. * Bit 7 - INTD MSK: External Interrupt D Mask * Bit 6 - INTC MSK: External Interrupt C Mask * Bit 5 - INTB MSK: External Interrupt B Mask * Bit 4 - INTA MSK: External Interrupt A Mask * Bit 3 - BUS INT MSK: USB Reset Interrupt Mask * Bit 2 - FRWUP MSK: Function Remote Wakeup Interrupt Mask * Bit 1 - RSM MSK: Resume Interrupt Mask * Bit 0 - GLB SUSP MSK: Global Suspend Interrupt Enable INTA/B/C/D Interrupt Sense Control Register - ISCR Bit $1FF1 Read/Write Initial Value 7 ISC71 6 ISC70 5 ISC61 4 ISC60 3 ISC51 2 ISC50 1 ISC41 0 ISC40 ISCR R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 * Bit 7,6 - ISC71, ISC70: External Interrupt D Sense Control Bits ISC71 and ISC70 controls the level and sense of the input at the INTD pin as defined below: ISC71 0 0 1 1 ISC70 0 1 0 1 Description Low level of INTD Reserved Falling edge of INTD Rising edge of INTD * Bit 5,4 - ISC61, ISC60: External Interrupt C Sense Control Bits ISC71 and ISC70 controls the level and sense of the input at the INTC pin as defined below: ISC61 0 0 1 1 ISC60 0 1 0 1 Description Low level of INTC Reserved Falling edge of INTC Rising edge of INTC * Bit 3,2 - ISC51, ISC40: External Interrupt B Sense Control Bits ISC51 and ISC50 controls the level and sense of the input at the INTB pin as defined below: 36 AT43USB325 3355A-USB-5/03 AT43USB325 ISC51 0 0 1 1 ISC50 0 1 0 1 Description Low level of INTB Reserved Falling edge of INTB Rising edge of INTB * Bit 1,0 - ISC41, ISC40: External Interrupt A Sense Control Bits ISC41 and ISC40 controls the level and sense of the input at the INTA pin as defined below: ISC41 0 0 1 1 ISC40 0 1 0 1 Description Low level of INTA Reserved Falling edge of INTA Rising edge of INTA 37 3355A-USB-5/03 AVR Register Set Status Register and Stack Pointer Status Register - SREG Bit $3F ($5F) Read/Write Initial Value 7 I R/W 0 6 T R/W 0 5 H R/W 0 4 S R/W 0 3 V R/W 0 2 N R/W 0 1 Z R/W 0 0 C R/W 0 SREG * Bit 7 - I: Global Interrupt Enable The global interrupt enable bit must be set (one) for the interrupts to be enabled. The individual interrupt enable control is then performed in separate control registers. If the global interrupt enable bit is cleared (zero), none of the interrupts are enabled independent of the individual interrupt enable settings. The I-bit is cleared by the hardware after an interrupt has occurred, and is set by the RETI instruction to enable subsequent interrupts. * Bit 6 - T: Bit Copy Storage The bit copy instructions BLD (Bit LoaD) and BST (Bit STore) use the T bit as source and destination for the operated bit. A bit from a register in the register file can be copied into T by the BST instruction, and a bit in T can be copied into a bit in a register in the register file by the BLD instruction. * Bit 5 - H: Half Carry Flag The half carry flag H indicates a half carry in some arithmetic operations. See the Instruction Set Description for detailed information. * Bit 4 - S: Sign Bit, S = NV The S-bit is always an exclusive or between the negative flag N and the two's complement overflow flag V. See the Instruction Set Description for detailed information. * Bit 3 - V: Two's Complement Overflow Flag The two's complement overflow flag V supports two's complement arithmetics. See the Instruction Set Description for detailed information. * Bit 2 - N: Negative Flag The negative flag N indicates a negative result after the different arithmetic and logic operations. See the Instruction Set Description for detailed information. * Bit 1 - Z: Zero Flag The zero flag Z indicates a zero result after the different arithmetic and logic operations. See the Instruction Set Description for detailed information. * Bit 0 - C: Carry Flag The carry flag C indicates a carry in an arithmetic or logic operation. See the Instruction Set Description for detailed information. Note that the status register is not automatically stored when entering an interrupt routine and restored when returning from an interrupt routine. This must be handled by software. 38 AT43USB325 3355A-USB-5/03 AT43USB325 Stack Pointer Register - SP Bit $3E ($5E) $3D ($5D) 15 I SP7 7 Read/Write R/W R/W Initial Value 0 0 14 T SP6 6 R/W R/W 0 0 13 H SP5 5 R/W R/W 0 0 12 S SP4 4 R/W R/W 0 0 11 V SP3 3 R/W R/W 0 0 10 N SP2 2 R/W R/W 0 0 9 Z SP1 1 R/W R/W 0 0 8 C SP0 0 R/W R/W 0 0 SPH SPL The Stack Pointer points to the data SRAM stack area where the Subroutine and Interrupt Stacks are located. This Stack space in the data SRAM must be defined by the program before any subroutine calls are executed or interrupts are enabled. The stack pointer must be set to point above $60. The Stack Pointer is decremented by one when data is pushed onto the Stack with the PUSH instruction, and it is decremented by two when an address is pushed onto the Stack with subroutine calls and interrupts. The Stack Pointer is incremented by one when data is popped from the Stack with the POP instruction and it is incremented by two when an address is popped from the Stack with return from subroutine RET or return from interrupt RETI. Sleep Modes To enter the sleep modes, the SE bit in MCUCR must be set (one) and a SLEEP instruction must be executed. If an enabled interrupt occurs while the MCU is in a sleep mode, the MCU awakes, executes the interrupt routine, and resumes execution from the instruction following SLEEP. The contents of the register file, SRAM and I/O memory are unaltered. If a reset occurs during sleep mode, the MCU wakes up and executes from the Reset vector. When the SM bit is set (one), the SLEEP instruction forces the MCU into the Power Down Mode. In this mode, the external oscillator is stopped, while the external interrupts continue operating. Only an external reset, an external level interrupt on INT0 or INT1, can wake up the MCU. Note that when a level triggered interrupt is used for wake-up from power down, the low level must be held for a time longer than the reset delay time-out period tTOUT. Otherwise, the MCU will fail to wake up. Power Down Mode 39 3355A-USB-5/03 Timer/Counters The AT43USB325 provides two general-purpose Timer/Counters - one 8-bit T/C and one 16bit T/C. The Timer/Counters have individual prescaling selection from the same 10-bit prescaling timer. Both Timer/Counters can either be used as a timer with an internal clock timebase or as a counter with an external pin connection which triggers the counting. The four different prescaled selections are: CK/8, CK/64, CK/256 and CK/1024 where CK is the oscillator clock. For the two Timer/Counters, added selections as CK, external source and stop, can be selected as clock sources. Timer/Counter Prescaler Figure 11. Timer/Counter Prescaler CK 10-bit T/C Prescaler CK/64 CK/256 0 T0 T1 0 CS10 CS11 CS12 CS00 CS01 CS02 Timer/Counter1 Clock Source TCK1 Timer/Counter0 Clock Source TCK0 40 AT43USB325 3355A-USB-5/03 CK/1024 CK/8 AT43USB325 8-bit Timer/Counter0 The 8-bit Timer/Counter0 can select clock source from CK, prescaled CK or an external pin. In addition it can be stopped as described in the specification for the Timer/Counter0 Control Register (TCCR0). The overflow status flag is found in the Timer/Counter Interrupt Flag Register (TIFR). Control signals are found in the Timer/Counter0 Control Register (TCCR0). The interrupt enable/disable settings for Timer/Counter0 are found in the Timer/Counter Interrupt Mask Register - TIMSK. When Timer/Counter0 is externally clocked, the external signal is synchronized with the oscillator frequency of the CPU. To assure proper sampling of the external clock, the minimum time between two external clock transitions must be at least one internal CPU clock period. The external clock signal is sampled on the rising edge of the internal CPU clock. The 8-bit Timer/Counter0 features both a high resolution and a high accuracy usage with the lower prescaling opportunities. Similarly, the high prescaling opportunities make the Timer/Counter0 useful for lower speed functions or exact timing functions with infrequent actions. Figure 12. Timer/Counter0 Block Diagram T/C0 Overflow IRQ 8-bit Data Bus TOIE1 OICIE1A OICIE1B TICIE1 TOIE0 Timer Int. Mask Register (TIMSK) Timer Int. Flag Register (TIFR) TOV1 OCF1A OCF1B TOV0 ICF1 TOV0 T/C0 Control Register (TCCR0) CS02 CS01 CS00 7 Timer/Counter0 (TCNT0) 0 T/C Clock Source Control Logic CK T0 41 3355A-USB-5/03 Timer/Counter0 Control Register - TCCR0 Bit $33 ($53) Read/Write Initial Value 7 - R 0 6 - R 0 5 - R 0 4 - R 0 3 - R 0 2 CS02 R/W 0 1 CS01 R/W 0 0 CS00 R/W 0 TCCR0 * Bits 7..3 - Res: Reserved Bits These bits are reserved bits in the AT43USB325 and always read as zero. * Bits 2, 1, 0 - CS02, CS01, CS00: Clock Select0, bit 2, 1 and 0 The Clock Select0 bits 2, 1 and 0 define the prescaling source of Timer/Counter0. Table 10. Clock 0 Prescale Select CS02 0 0 0 0 1 1 1 1 CS01 0 0 1 1 0 0 1 1 CS00 0 1 0 1 0 1 0 1 Description Stop, the Timer/Counter0 is stopped CK CK/8 CK/64 CK/256 CK/1024 External Pin T0, falling edge External Pin T0, rising edge The Stop condition provides a Timer Enable/Disable function. The CK down divided modes are scaled directly from the CK oscillator clock. If the external pin modes are used for Timer/Counter0, transitions on PB0/(T0) will clock the counter even if the pin is configured as an output. This feature can give the user SW control of the counting. Timer/Counter0 - TCNT0 Bit $32 ($52) Read/Write Initial Value 7 MSB R/W 0 6 - R/W 0 5 - R/W 0 4 - R/W 0 3 - R/W 0 2 - R/W 0 1 - R/W 0 0 LSB R/W 0 TCNT0 The Timer/Counter0 is realized as an up-counter with read and write access. If the Timer/Counter0 is written and a clock source is present, the Timer/Counter0 continues counting in the clock cycle following the write operation. 42 AT43USB325 3355A-USB-5/03 AT43USB325 16-bit Timer/Counter1 Figure 13. Timer/Counter1 Block Diagram T/C1 OVERFLOW IRQ T/C1 COMPARE MATCHA IRQ T/C1 COMPARE MATCHB IRQ T/C1INPUT CAPTURE IRQ 8-BIT DATA BUS TOIE1 OCIE1A OCIE1B TOV1 OCF1A OCF1B TICIE1 TOIE0 TIMER INT. MASK REGISTER (TIMSK) TOV1 TOV0 ICF1 TIMER INT. FLAG REGISTER (TIFR) OCF1A OCF1B ICF1 T/C1 CONTROL REGISTER A (TCCR1A) COM1A1 COM1A0 COM1B1 COM1B0 PWM11 PWM10 T/C1 CONTROL REGISTER B (TCCR1B) ICNC1 ICES1 CTC1 CS12 CS11 CS10 15 8 7 0 CONTROL LOGIC CK T1 T/C1 INPUT CAPTURE REGISTER (ICR1) CAPTURE TRIGGER 15 8 7 0 TIMER/COUNTER1 (TCNT1) 15 8 7 0 15 8 7 0 16-BIT COMPARATOR 16-BIT COMPARATOR 15 8 7 0 15 8 7 0 TIMER/COUNTER1 OUTPUT COMPARE REGISTER A TIMER/COUNTER1 OUTPUT COMPARE REGISTER B 43 3355A-USB-5/03 16-bit Timer/Counter1 Operation The 16-bit Timer/Counter1 can select clock source from CK, prescaled CK or an external pin. In addition, it can be stopped as described in the specification for the Timer/Counter1 Control Registers (TCCR1A and TCCR1B). The different status flags (overflow, compare match and capture event) are found in the Timer/Counter Interrupt Flag Register (TIFR). Control signals are found in the Timer/Counter1 Control Registers (TCCR1A and TCCR1B). The interrupt enable/disable settings for Timer/Counter1 are found in the Timer/Counter Interrupt Mask Register (TIMSK). When Timer/Counter1 is externally clocked, the external signal is synchronized with the oscillator frequency of the CPU. To assure proper sampling of the external clock, the minimum time between two external clock transitions must be at least one internal CPU clock period. The external clock signal is sampled on the rising edge of the internal CPU clock. The 16-bit Timer/Counter1 features both a high resolution and a high accuracy usage with the lower prescaling opportunities. Similarly, the high prescaling opportunities makes the Timer/Counter1 useful for lower speed functions or exact timing functions with infrequent actions. The Timer/Counter1 supports two Output Compare functions using the Output Compare Register 1 A and B (OCR1A and OCR1B) as the data sources to be compared to the Timer/Counter1 contents. The Output Compare functions include optional clearing of the counter on compareA match, and actions on the Output Compare pins on both compare matches. Timer/Counter1 can also be used as a 8-, 9- or 10-bit Pulse With Modulator. In this mode the counter and the OCR1A/OCR1B registers serve as a dual glitch-free stand-alone PWM with centered pulses. The Input Capture function of Timer/Counter1 provides a capture of the Timer/Counter1 contents to the Input Capture Register - ICR1, triggered by an external event on the Input Capture Pin (ICP/PF3). The actual capture event settings are defined by the Timer/Counter1 Control Register (TCCR1B). The AT43USB325 has no analog comparator and the mux control signal, ACO, is permanently set so that the ICP input is routed to the noise canceler. If the noise canceler function is enabled, the actual trigger condition for the capture event is monitored over 4 samples, and all 4 must be equal to activate the capture flag. Figure 14. ICP Pin Schematic Diagram 0 ICP 1 NOISE CANCELER EDGE SELECT ICF1 ICNC1 ICES1 ACIC ACO ACIC: COMPARATOR IC ENABLE ACC0: COMPARATOR OUTPUT 44 AT43USB325 3355A-USB-5/03 AT43USB325 Timer/Counter1 Control Register A - TCCR1A Bit $2F ($4F) Read/Write Initial Value 7 COM1A1 R/W 0 6 COM1A0 R/W 0 5 COM1B1 R/W 0 4 COM1B0 R/W 0 3 - R 0 2 - R 0 1 PWM11 R/W 0 0 PWM10 R/W 0 TCCR1A * Bits 7, 6 - COM1A1, COM1A0: Compare Output Mode1A, Bits 1 and 0 The COM1A1 and COM1A0 control bits determine any output pin action following a compare match in Timer/Counter1. Any output pin actions affect pin OC1A (Output CompareA) pin 1. This is an alternative function to an I/O port and the corresponding direction control bit must be set (one) to control the output pin. The control configuration is shown in Table 11. * Bits 5, 4 - COM1B1, COM1B0: Compare Output Mode1B, Bits 1 and 0 The COM1B1 and COM1B0 control bits determine any output pin action following a compare match in Timer/Counter1. Any output pin actions affect pin OC1B (Output CompareB). The following control configuration is given: Table 11. Compare 1 Mode Select(2) COM1X1 0 0 1 1 Note: 1. X = A or B 2. In PWM mode, these bits have a different function. Refer to Table 15 for a detailed description. COM1X0 0 1 0 1 Description Timer/Counter1 disconnected from output pin OC1X.(1) Toggle the OC1X output line.(1) Clear the OC1X output line (to zero).(1) Set the OC1X output line (to one).(1) * Bits 3..2 - Res: Reserved Bits These bits are reserved bits in the AT43USB325 and always read zero. * Bits 1..0 - PWM11, PWM10: Pulse Width Modulator Select Bits 1 and 0 These bits select PWM operation of Timer/Counter1 as specified in Table 12. Table 12. PWM Mode Select PWM11 0 0 1 1 PWM10 0 1 0 1 Description PWM operation of Timer/Counter1 is disabled. Timer/Counter1 is an 8-bit PWM. Timer/Counter1 is a 9-bit PWM. Timer/Counter1 is a 10-bit PWM. 45 3355A-USB-5/03 Timer/Counter1 Control Register B - TCCR1B Bit $2E ($4E) Read/Write Initial Value 7 ICNC1 R/W 0 6 ICES1 R/W 0 5 - R/W 0 4 - R/W 0 3 CTC1 R 0 2 CS12 R 0 1 CS11 R/W 0 0 CS10 R/W 0 TCCR1B * Bit 7 - ICNC1: Input Capture1 Noise Canceler (4 CKs) When the ICNC1 bit is cleared (zero), the input capture trigger noise canceler function is disabled. The input capture is triggered at the first rising/falling edge sampled on the ICP (input capture pin) as specified. When the ICNC1 bit is set (one), four successive samples are measured on the ICP and all samples must be high/low according to the input capture trigger specification in the ICES1 bit. The actual sampling frequency is the 12 MHz system clock frequency. * Bit 6 - ICES1: Input Capture1 Edge Select While the ICES1 bit is cleared (zero), the Timer/Counter1 contents are transferred to the Input Capture Register (ICR1) on the falling edge of the ICP. While the ICES1 bit is set (one), the Timer/Counter1 contents are transferred to the ICR1 on the rising edge of the ICP. * Bits 5, 4 - Res: Reserved Bits These bits are reserved bits in the AT43USB325 and always read zero. * Bit 3 - CTC1: Clear Timer/Counter1 on Compare Match When the CTC1 control bit is set (one), the Timer/Counter1 is reset to $0000 in the clock cycle after a compareA match. If the CTC1 control bit is cleared, Timer/Counter1 continues counting and is unaffected by a compare match. Since the compare match is detected in the CPU clock cycle following the match, this function will behave differently when a prescaling higher than 1 is used for the timer. When a prescaling of 1 is used, and the compareA register is set to C, the timer will count as follows if CTC1 is set: ... | C-2 | C-1 | C | 0 | 1 | ... When the prescaler is set to divide by 8, the timer will count like this: ... | C-2, C-2, C-2, C-2, C-2, C-2, C-2, C-2 | C-1, C-1, C-1, C-1, C-1, C-1, C-1, C-1 | C, 0, 0, 0, 0, 0, 0, 0 | ... In PWM mode, this bit has no effect. * Bits 2, 1, 0 - CS12, CS11, CS10: Clock Select1, Bit 2, 1 and 0 The Clock Select1 bits 2, 1 and 0 define the prescaling source of Timer/Counter1. Table 13. Clock 1 Prescale Select CS12 0 0 0 0 1 CS11 0 0 1 1 0 CS10 0 1 0 1 0 Description Stop, the Timer/Counter1 is stopped. CK CK/8 CK/64 CK/256 46 AT43USB325 3355A-USB-5/03 AT43USB325 Table 13. Clock 1 Prescale Select (Continued) CS12 1 1 1 CS11 0 1 1 CS10 1 0 1 Description CK/1024 External Pin T1, falling edge External Pin T1, rising edge The Stop condition provides a Timer Enable/Disable function. The CK down divided modes are scaled directly from the 12 MHz system clock. If the external pin modes are used for Timer/Counter1, transitions on PB1/(T1) will clock the counter even if the pin is configured as an output. This feature can give the user SW control of the counting. Timer/Counter1 - TCNT1H and TCNT1L Bit $2D ($4D) $2C ($4C) 15 MSB - 7 Read/Write R/W R/W Initial Value 0 0 14 - - 6 R/W R/W 0 0 13 - - 5 R/W R/W 0 0 12 - - 4 R/W R/W 0 0 11 - - 3 R/W R/W 0 0 10 - - 2 R/W R/W 0 0 9 - - 1 R/W R/W 0 0 8 - LSB 0 R/W R/W 0 0 TCNT1H TCNT1L This 16-bit register contains the prescaled value of the 16-bit Timer/Counter1. To ensure that both the high and low bytes are read and written simultaneously when the CPU accesses these registers, the access is performed using an 8-bit temporary register (TEMP). This temporary register is also used when accessing OCR1A, OCR1B and ICR1. If the main program and also interrupt routines perform access to registers using TEMP, interrupts must be disabled during access from the main program and from interrupt routines if interrupts are allowed from within interrupt routines. * TCNT1 Timer/Counter1 Write: When the CPU writes to the high byte TCNT1H, the written data is placed in the TEMP register. Next, when the CPU writes the low byte TCNT1L, this byte of data is combined with the byte data in the TEMP register, and all 16 bits are written to the TCNT1 Timer/Counter1 register simultaneously. Consequently, the high byte TCNT1H must be accessed first for a full 16bit register write operation. * TCNT1 Timer/Counter1 Read: When the CPU reads the low byte TCNT1L, the data of the low byte TCNT1L is sent to the CPU and the data of the high byte TCNT1H is placed in the TEMP register. When the CPU reads the data in the high byte TCNT1H, the CPU receives the data in the TEMP register. Consequently, the low byte TCNT1L must be accessed first for a full 16-bit register read operation. The Timer/Counter1 is realized as an up or up/down (in PWM mode) counter with read and write access. If Timer/Counter1 is written to and a clock source is selected, the Timer/Counter1 continues counting in the timer clock cycle after it is preset with the written value. 47 3355A-USB-5/03 Timer/Counter1 Output Compare Register - OCR1AH and OCR1AL Bit $2B ($4B) $2A ($4A) 15 MSB - 7 Read/Write R/W R/W Initial Value 0 0 14 - - 6 R/W R/W 0 0 13 - - 5 R/W R/W 0 0 12 - - 4 R/W R/W 0 0 11 - - 3 R/W R/W 0 0 10 - - 2 R/W R/W 0 0 9 - - 1 R/W R/W 0 0 8 - LSB 0 R/W R/W 0 0 OCR1AH OCR1AL Timer/Counter1 Output Compare Register - OCR1BH and OCR1BL Bit $29 ($49) $28 ($48) 15 MSB - 7 Read/Write R/W R/W Initial Value 0 0 14 - - 6 R/W R/W 0 0 13 - - 5 R/W R/W 0 0 12 - - 4 R/W R/W 0 0 11 - - 3 R/W R/W 0 0 10 - - 2 R/W R/W 0 0 9 - - 1 R/W R/W 0 0 8 - LSB 0 R/W R/W 0 0 OCR1BH OCR1BL The output compare registers are 16-bit read/write registers. The Timer/Counter1 Output Compare Registers contain the data to be continuously compared with Timer/Counter1. Actions on compare matches are specified in the Timer/Counter1 Control and Status register.A compare match does only occur if Timer/Counter1 counts to the OCR value. A software write that sets TCNT1 and OCR1A or OCR1B to the same value does not generate a compare match. A compare match will set the compare interrupt flag in the CPU clock cycle following the compare event. Since the Output Compare Registers OCR1A and OCR1B are 16-bit registers, a temporary register TEMP is used when OCR1A/B are written to ensure that both bytes are updated simultaneously. When the CPU writes the high byte, OCR1AH or OCR1BH, the data is temporarily stored in the TEMP register. When the CPU writes the low byte, OCR1AL or OCR1BL, the TEMP register is simultaneously written to OCR1AH or OCR1BH. Consequently, the high byte OCR1AH or OCR1BH must be written first for a full 16-bit register write operation. The TEMP register is also used when accessing TCNT1, and ICR1. If the main program and also interrupt routines perform access to registers using TEMP, interrupts must be disabled during access from the main program and from interrupt routines if interrupts are allowed from within interrupt routines. 48 AT43USB325 3355A-USB-5/03 AT43USB325 Timer/Counter1 Input Capture Register - ICR1H and ICR1L Bit $25 ($45) $24 ($44) 15 MSB - 7 Read/Write R R Initial Value 0 0 14 - - 6 R R 0 0 13 - - 5 R R 0 0 12 - - 4 R R 0 0 11 - - 3 R R 0 0 10 - - 2 R R 0 0 9 - - 1 R R 0 0 8 - LSB 0 R R 0 0 ICR1H ICR1L The input capture register is a 16-bit read-only register. When the rising or falling edge (according to the input capture edge setting - ICES1) of the signal at the input capture pin (ICP) is detected, the current value of the Timer/Counter1 is transferred to the Input Capture Register (ICR1). At the same time, the Input Capture Flag (ICF1) is set (one). Since the ICR1 is a 16-bit register, a temporary register TEMP is used when ICR1 is read to ensure that both bytes are read simultaneously. When the CPU reads the low byte ICR1L, the data is sent to the CPU and the data of the high byte ICR1H is placed in the TEMP register. When the CPU reads the data in the high byte ICR1H, the CPU receives the data in the TEMP register. Consequently, the low byte ICR1L must be accessed first for a full 16-bit register read operation. The TEMP register is also used when accessing TCNT1, OCR1A and OCR1B. If the main program and also interrupt routines perform access to registers using TEMP, interrupts must be disabled during access from the main program and from interrupt routines, if interrupts are allowed from within interrupt routines. Timer/Counter1 In PWM Mode When the PWM mode is selected, Timer/Counter1, the Output Compare Register1A (OCR1A) and the Output Compare Register1B (OCR1B) form a dual 8-, 9- or 10-bit, free-running, glitchfree and phase correc t PW M with outputs on the PD5 (OC1A) and OC1B pins. Timer/Counter1 acts as an up/down counter, counting up from $0000 to TOP (see Table 14), where it turns and counts down again to zero before the cycle is repeated. When the counter value matches the contents of the 10 least significant bits of OCR1A or OCR1B, the PD5(OC1A)/OC1B pins are set or cleared according to the settings of the COM1A1/COM1A0 or COM1B1/COM1B0 bits in the Timer/Counter1 Control Register TCCR1A. Refer to Table 15 for details. Table 14. Timer TOP Values and PWM Frequency PWM Resolution 8-bit 9-bit 10-bit Timer TOP value $00FF (255) $01FF (511) $03FF(1023) Frequency fTCK1/510 fTCK1/1022 fTCK1/2046 49 3355A-USB-5/03 Table 15. Compare1 Mode Select in PWM Mode COM1X1 0 0 1 1 Note: X = A or B COM1X0 0 1 0 1 Effect on OCX1 Not connected Not connected Cleared on compare match, up-counting. Set on compare match, down-counting (non-inverted PWM). Cleared on compare match, down-counting. Set on compare match, up-counting (inverted PWM). Note that in the PWM mode, the 10 least significant OCR1A/OCR1B bits, when written, are transferred to a temporary location. They are latched when Timer/Counter1 reaches the value TOP. This prevents the occurrence of odd-length PWM pulses (glitches) in the event of an unsynchronized OCR1A/OCR1B write. See Figure 15 for an example. Figure 15. Effects on Unsynchronized OCR1 Latching Compare Value Changes Counter Value Compare Value PWM Output OC1X Synchronized OCR1X Latch Compare Value Changes Counter Value Compare Value PWM Output OC1X Unsynchronized OCR1X Latch Glitch Note: X = A or B During the time between the write and the latch operation, a read from OCR1A or OCR1B will read the contents of the temporary location. This means that the most recently written value always will read out of OCR1A/B When the OCR1 contains $0000 or TOP, the output OC1A/OC1B is updated to low or high on the next compare match, according to the settings of COM1A1/COM1A0 or COM1B1/COM1B0. This is shown in Table 16. Note: If the compare register contains the TOP value and the prescaler is not in use (CS12..CS10 = 001), the PWM output will not produce any pulse at all, because up-counting and down-counting values are reached simultaneously. When the prescaler is in use 50 AT43USB325 3355A-USB-5/03 AT43USB325 (CS12..CS10 = 001 or 000), the PWM output goes active when the counter reaches the TOP value, but the down-counting compare match is not interpreted to be reached before the next time the counter reaches the TOP value, making a one-period PWM pulse. Table 16. PWM Outputs OCR1X = $0000 or Top COM1X1 1 1 1 1 Note: X = A or B COM1X0 0 0 1 1 OCR1X $0000 TOP $0000 TOP Output OC1X L H H L In PWM mode, the Timer Overflow Flag1, TOV1, is set when the counter advances from $0000. Timer Overflow Interrupt1 operates exactly as in normal Timer/Counter mode, i.e. it is executed when TOV1 is set provided that Timer Overflow Interrupt1 and global interrupts are enabled. This also applies to the Timer Output Compare1 flags and interrupts. Watchdog Timer The Watchdog Timer is clocked from a 1 MHz clock derived from the 6 MHz on chip oscillator. By controlling the Watchdog Timer prescaler, the Watchdog reset interval can be adjusted, see Table 17 for a detailed description. The WDR (Watchdog Reset) instruction resets the Watchdog Timer. Eight different clock cycle periods can be selected to determine the reset period. If the reset period expires without another Watchdog reset, the AT43USB325 resets and executes from the reset vector. To prevent unintentional disabling of the watchdog, a special turn-off sequence must be followed when the watchdog is disabled. Refer to the description of the Watchdog Timer Control Register for details. Figure 16. Watchdog Timer 1 MHz Clock Watchdog Prescaler OSC/1024K OSC/2048K OSC/16K OSC/32K OSC/64K OSC/128K OSC/256K OSC/512K Watchdog Reset WDP0 WDP1 WDP2 WDE MCU Reset 51 3355A-USB-5/03 Timer/Counter1 Control Register A - TCCR1A Bit $21 ($41) Read/Write Initial Value 7 - R 0 6 - R 0 5 - R 0 4 WDTOE R/W 0 3 WDE R/W 0 2 WDP2 R/W 0 1 WDP1 R/W 0 0 WDP0 R/W 0 WDTCR * Bits 7..5 - Res: Reserved Bits These bits are reserved bits in the AT43USB325 and will always read as zero. * Bit 4 - WDTOE: Watch Dog Turn-Off Enable This bit must be set (one) when the WDE bit is cleared. Otherwise, the watchdog will not be disabled. Once set, the hardware will clear this bit to zero after four clock cycles. Refer to the description of the WDE bit for a watchdog disable procedure. * Bit 3 - WDE: Watch Dog Enable When the WDE is set (one) the Watchdog Timer is enabled, and if the WDE is cleared (zero) the Watchdog Timer function is disabled. WDE can only be cleared if the WDTOE bit is set (one). To disable an enabled watchdog timer, the following procedure must be followed: 1. In the same operation, write a logical one to WDTOE and WDE. A logical one must be written to WDE even though it is set to one before the disable operation starts. 2. Within the next four clock cycles, write a logical 0 to WDE. This disables the watchdog. * Bits 2..0 - WDP2, WDP1, WDP0: Watch Dog Timer Prescaler 2, 1 and 0 The WDP2, WDP1 and WDP0 bits determine the Watchdog Timer prescaling when the Watchdog Timer is enabled. The different prescaling values and their corresponding Time-out Periods are shown in Table 17. Table 17. Watchdog Timer Prescale Select WDP2 0 0 0 0 1 1 1 1 Note: WDP1 0 0 1 1 0 0 1 1 WDP0 0 1 0 1 0 1 0 1 Number of WDT Oscillator cycles 16K cycles 32K cycles 64K cycles 128K cycles 256K cycles 512K cycles 1,024K cycles 2,048K cycles Time-out 15 ms 30 ms 60 ms 0.12 s 0.24 s 0.49 s 0.97 s 1.9 s The WDR (Watchdog Reset) instruction should always be executed before the Watchdog Timer is enabled. This ensures that the reset period will be in accordance with the Watchdog Timer prescale settings. If the Watchdog Timer is enabled without reset, the watchdog timer may not start to count from zero. To avoid unintentional MCU reset, the Watchdog Timer should be disabled or reset before changing the Watchdog Timer Prescale Select. 52 AT43USB325 3355A-USB-5/03 AT43USB325 I/O Ports All GPIO ports have true Read-Modify-Write functionality when used as general digital I/O ports. This means that the direction of one port pin can be changed without unintentionally changing the direction of any other pin with the SBI and CBI instructions. The same applies for changing drive value if configured as output or enabling/disabling of pull-up resistors if configured as input. The keyboard matrix strobe output pins, PA[0:7], PB[0:7] and PE[0:3] have controlled slope drivers. With a load of 100 pF, the output fall time ranges between 75 ns and 300 ns. The keyboard matrix strobe input pins, PC[0:7] have When the FE3 IMSK bit is set (1), the Function End-point 3 Interrupt is masked. PE[4:7] have 5V tolerant outputs and each has a built-in series resistor of 330 nominal value. These output pins are designed for driving an LED connected to the 5V supply. The dedicated functions are summarized in Table 18. Table 18. GPIO Function Assignments Function Scan out[0:7] Scan out[8:15] Scan out[16:19] Scan in[0:7] LED drivers EEPROM Interface GPIO PA[0:7] PB[0:7] PE[0:3] PC[0:7] PE[4:7] PF[1:3] In the AT43USB325E Port F[0:3] are used as the SPI signals for the external serial EEPROM. Once the data from the SEEPROM are loaded to the SRAM, Port F[1:3] become available as GPIO pins. Only cycling the power to the chip off and on again will temporarily assign these pins as EEPOM signals. 53 3355A-USB-5/03 Port A Port A is an 8-bit bi-directional I/O port with open drain outputs and controlled slew rate. It is designed for use as the column driver in a keyboard controller. The Port A output buffers can sink or source 4 mA. Three I/O memory address locations are allocated for the Port A, one each for the Data Register PORTA, $1B($3B), Data Direction Register (DDRA), $1A($3A) and the Port A Input Pins (PINA) $19($39). The Port A Input Pins address is read only, while the Data Register and the Data Direction Register are read/write. Port A Data Register - PORTA Bit $1B ($3B) Read/Write Initial Value 7 PORTA7 R/W 0 6 PORTA6 R/W 0 5 PORTA5 R/W 0 4 PORTA4 R/W 0 3 PORTA3 R/W 0 2 PORTA2 R/W 0 1 PORTA1 R/W 0 0 PORTA0 R/W 0 PORTA Port A Data Direction Register - DDRA Bit $1A ($3A) Read/Write Initial Value 7 DDA7 R/W 0 6 DDA6 R/W 0 5 DDA5 R/W 0 4 DDA4 R/W 0 3 DDA3 R/W 0 2 DDA2 R/W 0 1 DDA1 R/W 0 0 DDA0 R/W 0 DDRA Port A Input Pins Address - PINA Bit $19 ($39) Read/Write Initial Value 7 PINA7 R N/A 6 PINA6 R N/A 5 PINA5 R N/A 4 PINA4 R N/A 3 PINA3 R N/A 2 PINA2 R N/A 1 PINA1 R N/A 0 PINA0 R N/A PINA The Port A Input Pins address (PINA) is not a register, and this address enables access to the physical value on each Port A pin. When reading PORTA the Port A Data Latch is read, and when reading PINA, the logical values present on the pins are read. 54 AT43USB325 3355A-USB-5/03 AT43USB325 Port B Port B is an 8-bit bi-directional I/O port with open drain outputs and controlled slew rate. It is designed for use as the column driver in a keyboard controller. The Port B output buffers can sink or source 4 mA. Three I/O memory address locations are allocated for the Port B, one each for the Data Register - PORTB, $18($38), Data Direction Register (DDRB), $17($37) and the Port B Input Pins (PINB), $16($36). The Port B Input Pins address is read only, while the Data Register and the Data Direction Register are read/write. Port B Data Register - PORTB Bit $18 ($38) Read/Write Initial Value 7 PORTB7 R/W 0 6 PORTB6 R/W 0 5 PORTB5 R/W 0 4 PORTB4 R/W 0 3 PORTB3 R/W 0 2 PORTB2 R/W 0 1 PORTB1 R/W 0 0 PORTB0 R/W 0 PORTB Port B Data Direction Register - DDRB Bit $17 ($37) Read/Write Initial Value 7 DDB7 R/W 0 6 DDB6 R/W 0 5 DDB5 R/W 0 4 DDB4 R/W 0 3 DDB3 R/W 0 2 DDB2 R/W 0 1 DDB1 R/W 0 0 DDB0 R/W 0 DDRB Port B Input Pins Address - PINB Bit $16 ($36) Read/Write Initial Value 7 PINB7 R N/A 6 PINB6 R N/A 5 PINB5 R N/A 4 PINB4 R N/A 3 PINB3 R N/A 2 PINB2 R N/A 1 PINB1 R N/A 0 PINB0 R N/A PINB The Port B Input Pins address (PINB) is not a register, and this address enables access to the physical value on each Port B pin. When reading PORTB, the Port B Data Latch is read, and when reading PINB, the logical values present on the pins are read. 55 3355A-USB-5/03 Port C Port C is an 8-bit bi-directional I/O port with an internal pull-up resistor at each pin. Port C is designed for use as the row inputs of a keyboard controller. Its output buffers can sink 4 mA. Three I/O memory address locations are allocated for the Port C, one each for the Data Register - PORTC, $15($35), Data Direction Register - DDRC, $14($34) and the Port C Input Pins - PINC, $13($33). The Port C Input Pin's address is read only, while the Data Register and the Data Direction Register are read/write. Port C Data Register - PORTC Bit $15 ($35) Read/Write Initial Value 7 PORTC7 R/W 0 6 PORTC6 R/W 0 5 PORTC5 R/W 0 4 PORTC4 R/W 0 3 PORTC3 R/W 0 2 PORTC2 R/W 0 1 PORTC1 R/W 0 0 PORTC0 R/W 0 PORTC Port C Data Direction Register - DDRC Bit $14 ($34) Read/Write Initial Value 7 DDC7 R/W 0 6 DDC6 R/W 0 5 DDC5 R/W 0 4 DDC4 R/W 0 3 DDC3 R/W 0 2 DDC2 R/W 0 1 DDC1 R/W 0 0 DDC0 R/W 0 DDRC Port C Input Pins Address - PINC Bit $13 ($33) Read/Write Initial Value 7 PINC7 R N/A 6 PINC6 R N/A 5 PINC5 R N/A 4 PINC4 R N/A 3 PINC3 R N/A 2 PINC2 R N/A 1 PINC1 R N/A 0 PINC0 R N/A PINC The Port C Input Pins address (PINC) is not a register, and this address enables access to the physical value on each Port C pin. When reading PORTC, the Port C Data Latch is read, and when reading PINC, the logical values present on the pins are read. 56 AT43USB325 3355A-USB-5/03 AT43USB325 Port D Port D is a 7-bit bi-directional I/O port. Three I/O memory address locations are allocated for the Port D, one each for the Data Register - PORTD, $12($32), Data Direction Register - DDRD, $11($31) and the Port D Input Pins PIND, $10($30). The Port D Input Pins address is read only, while the Data Register and the Data Direction Register are read/write. Some Port D pins have alternate functions as shown in the following table: Table 19. Port D Pins Alternate Functions Port Pin PD1 PD3 PD4 PD5 PD6 PD7 Alternate Function T1 (Timer/Counter1 External Counter Input) INT1 (External Interrupt 1 Input) INTA (External Interrupt A Input) INTB (External Interrupt B Input) INTC (External Interrupt C Input) INTD (External Interrupt D Input) When the pins are used for the alternate function the DDRD and PORTD register has to be set according to the alternate function description. Port D Data Register - PORTD Bit $12 ($32) Read/Write Initial Value 7 PORTD7 R/W 0 6 PORTD6 R/W 0 5 PORTD5 R/W 0 4 PORTD4 R/W 0 3 PORTD3 R/W 0 2 - - 0 1 PORTD1 R/W 0 0 PORTD0 R/W 0 PORTD Port D Data Direction Register - DDRD Bit $11 ($31) Read/Write Initial Value 7 DDD7 R/W 0 6 DDD6 R/W 0 5 DDD5 R/W 0 4 DDD4 R/W 0 3 DDD3 R/W 0 2 - - 0 1 DDD1 R/W 0 0 DDD0 R/W 0 DDRD Port D Input Pins Address - PIND Bit $10 ($30) Read/Write Initial Value 7 PIND7 R N/A 6 PIND6 R N/A 5 PIND5 R N/A 4 PIND4 R N/A 3 PIND3 R N/A 2 - - N/A 1 PIND1 R N/A 0 PIND0 R N/A PIND The Port D Input Pins address (PIND) is not a register, and this address enables access to the physical value on each Port D pin. When reading PORTD, the Port D Data Latch is read, and when reading PIND, the logical values present on the pins are read. 57 3355A-USB-5/03 Port D as General Digital I/O PDn, General I/O Pin: The DDDn bit in the DDRD register selects the direction of this pin. If DDDn is set (one), PDn is con-figured as an output pin. If DDDn is cleared (zero), PDn is configured as an input pin. The value of PORTDn has no meaning in this mode. The Port D pins are tri-stated when a reset condition becomes active. Table 20. DDDn Bits on Port D Pins DDDn 0 0 1 1 Note: PORTDn 0 1 0 1 I/O Input Input Output Output Comment Tri-state (Hi-Z) Tri-state (Hi-Z) Push-pull Zero Output Push-pull One Output n: 7,6,5,4,3,1,0, pin number Alternate Functions of Port D INT1, External Interrupt Source 1: The PD3 pin can serve as an external interrupt source to the MCU. See the interrupt description for further details, and how to enable the source. 58 AT43USB325 3355A-USB-5/03 AT43USB325 Port E Port E[0:3] each is a bi-directional I/O port with open drain outputs and controlled slew rate and is designed for use as the column drivers in a keyboard controller. The Port E[0:3] output buffers can sink 4 mA. Port E[4:7] are bi-directional I/O with outputs capable of driving LEDs directly. Each pin of Port E[4:7] has a series resistor to limit the LEDs current. Three I/O memory address locations are allocated for the Port E, one each for the Data Register - PORTE, $03($23), Data Direction Register - DDRE, $02($22) and the Port E Input Pins PINE, $01($21). The Port E Input Pins address is read only, while the Data Register and the Data Direction Register are read/write. Port E Data Register - PORTE Bit $03($23) Read/Write Initial Value 7 PORTE7 R/W 0 6 PORTE6 R/W 0 5 PORTE5 R/W 0 4 PORTE4 R/W 0 3 PORTE3 R/W 0 2 PORTE2 R/W 0 1 PORTE1 R/W 0 0 PORTE0 R/W 0 PORTE Port E Data Direction Register - DDRE Bit $02 ($22) Read/Write Initial Value 7 DDE7 R/W 0 6 DDE6 R/W 0 5 DDE5 R/W 0 4 DDE4 R/W 0 3 DDE3 R/W 0 2 DDE2 R/W 0 1 DDE1 R/W 0 0 DDE0 R/W 0 DDRE Port E Input Pins Address - PINE Bit $01 ($21) Read/Write Initial Value 7 PINE7 R/W N/A 6 PINE6 R/W N/A 5 PINE5 R/W N/A 4 PINE4 R/W N/A 3 PINE3 R/W N/A 2 PINE2 R/W N/A 1 PINE1 R N/A 0 PINE0 R N/A PINE The Port E Input Pins address, PINE, is not a register, and this address enables access to the physical value on each Port E pin. When reading PORTE the Port E Data Latch is read, and when reading PINE, the logical values present on the pins are read. Port E as General Digital I/O PEn, General I/O Pin: The DDEn bit in the DDRE register selects the direction of this pin. If DDEn is set (one), PEn is con-figured as an output pin. If DDEn is cleared (zero), PEn is configured as an input pin. The value of PORTEn has no meaning in this mode. The Port E pins are tri-stated when a reset condition becomes active. Table 21. DDEn Bits on Port E Pins DDEn 0 0 1 1 Note: PORTEn 0 1 0 1 I/O Input Input Output Output Comment Tri-state (Hi-Z) Tri-state (Hi-Z) Push-pull Zero Output Push-pull One Output n: 7,6...0, pin number 59 3355A-USB-5/03 Port F Port F[1:3] is a 3-bit bi-directional I/O that becomes available after the program memory is written at the end of POR. Three I/O memory address locations are allocated for the Port F, one each for the Data Register - PORTF, $06($26), Data Direction Register - DDRF, $05($25) and the Port F Input Pins - PIND, $04($24). The Port F Input Pins address is read only, while the Data Register and the Data Direction Register are read/write. Some Port F pins have alternate functions as shown in the following table: Table 22. Port F Pins Alternate Functions Port Pin PF1 PF2 PF3 Alternate Function 1 SCK (SPI Bus Serial Clock) MOSI (SPI Bus Master Output/Slave Input) MISO (SPI Bus Master Input/Slave Output) Alternate Function 2 OC1A (Timer/Counter1 Output CompareA Match Output) OC1B (Timer/Counter1 Output CompareB Match Output) ICP (Timer/Counter1 Input Capture) After power up, PF[1:3] are used to load the program memory. This process is automatic. After completion of program memory downloading, the SSN pin is de-asserted (=logic 1) and the pins functions as GPIOs. When the pins are used for the alternate function, after downloading is completed, the DDRF and PORTF register has to be set according to the alternate function description. Port F Data Register - PORTF Bit $06($26) Read/Write Initial Value 7 R/W 0 6 R/W 0 5 R/W 0 4 R/W 0 3 PORTF3 R/W 0 2 PORTF2 R/W 0 1 PORTF1 R/W 0 0 R/W 0 PORTF Port F Data Direction Register - DDRF Bit $05($25) Read/Write Initial Value 7 R/W 0 6 R/W 0 5 R/W 0 4 R/W 0 3 DDF3 R/W 0 2 DDF2 R/W 0 1 DDF1 R/W 0 0 R/W 0 DDRF Port F Input Pin Address - PINF Bit $04($24) Read/Write Initial Value 7 R N/A 6 R N/A 5 R N/A 4 R N/A 3 PINF3 R N/A 2 PINF2 R N/A 1 PINF1 R N/A 0 R N/A PINF The Port F Input Pins address - PINF - is not a register, and this address enables access to the physical value on each Port F pin. When reading PORTF, the Port F Data Latch is read, and when reading PINF, the logical values present on the pins are read. 60 AT43USB325 3355A-USB-5/03 AT43USB325 Port F as General Digital I/O PFn, General I/O Pin: After firmware downloading, the DDFn bit in the DDRF register selects the direction of this pin. If DDFn is set (one), PFn is con-figured as an output pin. If DDFn is cleared (zero), PFn is configured as an input pin. The value of PORTFn has no meaning in this mode. The Port F pins are tri-stated when a reset condition becomes active. Table 23. DDFn Bits on Port F Pins DDFn 0 0 1 1 Note: n: 3,2,1, pin number PORTFn 0 1 0 1 I/O Input Input Output Output Comment Tri-state (Hi-Z) Tri-state (Hi-Z) Push-pull Zero Output Push-pull One Output 61 3355A-USB-5/03 Programming the USB Module The USB hardware consists of two devices, hub and function, each with their own device address and endpoints. Its operation is controlled through a set of memory mapped registers. The exact configuration of the USB device is defined by the software and it can be programmed to operate as a compound device, or as a hub only or as a function only. The hub has the required control and interrupt endpoints. The number of external downstream ports is programmable from 0 to 2. The DP and DM pins of the unused port(s) must be connected to ground. The USB function has one control endpoint and 2 programmable endpoints. All the endpoints have their own 8-byte FIFOs. If the hub is disabled, one extra endpoint becomes available to the function. The USB function hardware is designed to operate in the single packet mode and to manage the USB protocol layer. It consists of a Serial Interface Engine (SIE), endpoint FIFOs and a Function Interface Unit (FIU). The SIE performs the following tasks: USB signaling detection/generation, data serialization/de-serialization, data encoding/decoding, bit stuffing and unstuffing, clock/data separation, and CRC generation/checking. It also decodes and manages all packet data types and packet fields. The endpoint FIFO buffers the data to be sent out or data received. The FIU manages the flow of data between the SIE, FIFO and the internal microcontroller bus. It controls the FIFO and monitors the status of the transactions and interfaces to the CPU. It initiates interrupts and acts upon commands sent by the firmware. The USB function hardware of the AT43USB325 makes the physical interface and the protocol layer transparent to the user. To start the process, the firmware must first enable the endpoints and which place them in receive mode by default. The device address by default is address 0. The USB function hardware then waits for a setup token from the host. When a valid setup token is received, it automatically stores the data packet in endpoint 0 FIFO and responds with an ACK. It then notifies the microcontroller through an interrupt. The microcontroller reads the FIFO and parses the request. Transactions for the non-control endpoints are even simpler. Once the endpoint is enabled, it waits for an IN or an OUT token depending whether it is programmed as an IN or OUT endpoint. For example, if it is an IN endpoint, the microcontroller simply loads the data into the endpoint's FIFO and sets a bit in the control and status register. The USB hardware will assemble the data in a USB packet and waits for an IN token. When it receives one, it automatically responds by transmitting the data packet and completes the transaction by waiting for the host's ACK. When one is received, the USB hardware will signal the microcontroller that the transaction has been completed successfully. Retries and data toggles are performed automatically by the USB hardware. When the IN endpoint is not ready to send data, in the case where the microcontroller has not filled the FIFO, it will automatically respond with a NAK. Similarly, an OUT endpoint will wait for an OUT token. When one is received, it will store the data in the FIFO, completes the transaction and interrupt the microcontroller, which then reads the FIFO and enables the endpoint for the next packet. If the FIFO is not cleared, the USB hardware will responds with a NAK. A detailed description of how USB transactions are handled is described in the following sections. First for a control endpoint and then for non-control endpoints. The USB Function 62 AT43USB325 3355A-USB-5/03 AT43USB325 Control Transfers at Control End-point EP0 The description given below is for the function control end-point, but applies to the hub control end-point as well if the proper registers are used. The following illustration describes the three possible types of control transfers - Control Write, Control Read and No-data control: Setup Stage Control Write Control Read SETUP(0) DATA0 Data Stage OUT(1) DATA1 Status Stage ... OUT(0/1) DATA0/1 OUT(0) DATA0 IN(1) DATA1(0) SETUP(0) DATA0 IN(1) DATA1 IN(0) DATA0 ... IN(0/1) DATA0/1 OUT(1) DATA1(0) Setup Stage No-data Control SETUP(0) DATA0 Status Stage Legend: IN(1) DATA1(0) DATAn DATA1(0) Data packet with PID's data toggle bit equal to n Zero length DATA1 packet The following state diagram shows how the various state transitions are triggered. Additional decision making may take place within the response states to determine the next expected state. Unmarked arcs represent transitions that trigger immediately following completion of the response state processing. Stable states, those requiring an interrupt to exit having no unmarked arcs as exit paths, are shown in bold. 63 3355A-USB-5/03 (ANY STABLE STATE) RX_SETUP_INT Setup Response RX_OUT_INT TX_COMPLETE_INT TX_COMPLETE_INT Control Write Data Response Control Read Data Response No-data Status Response RX_OUT_INT TX_COMPLETE_INT TX_COMPLETE_INT RX_OUT_INT Control Write Status Response Control Read Status Response Idle The following information describes how the AT43USB325's USB hardware and firmware operates during a control transfer between the host and the hub's or function's control endpoint. Legend: DATA1/DATA0 = Data packet with DATA1 or DATA2 PID DATA1(0) = Zero length DATA1 packet Idle State Setup Response State This is the default state from power-up. The Function Interface Unit (FIU) receives a SETUP token with 8 bytes of data from the Host. The FIU stores the data in the FIFO, sends an ACK back to the host and asserts an RX_SETUP interrupt. Hardware 1. SETUP token, DATA from Host 2. ACK to Host 3. Store data in FIFO 4. Set RX SETUP INT 5. Read UISR 6. Read CSR0 64 Firmware AT43USB325 3355A-USB-5/03 AT43USB325 7. Read Byte Count 8. Read FIFO 9. Parse command data 10. Write to H/FCAR0: a. If Control Read: set DIR, clear RX SETUP, fill FIFO, set TX Packet Ready in CAR0 b. If Control Write: clear DIR in CAR0 c. If no Data Stage: set Data End, clear DIR, set Force STALL in CAR0 11. Set UIAR[EP0 INTACK] to clear the interrupt source 65 3355A-USB-5/03 No-data Status Response State The Function Interface Unit receives an IN token from the Host. The FIU responds with a zero length DATA1 packet until receiving an ACK from the host, then asserts a TX_COMPLETE interrupt. Hardware 1. IN token from Host 2. Send DATA1(0) 3. ACK from Host 4. Set TX COMPLETE INT 5. Read UISR 6. Read CSR0 Firmware 7. If SET ADDRESS, program the new Address, set ADD_EN bit 8. Clear TX_COMPLETE, clear Data End, set Force STALL in CAR0 9. Set UIAR[EP0 INTACK] Control Read Data Response State The Function Interface Unit receives an IN token from the Host. The FIU responds with NAKs until TX_PACKET_READY is set. The FIU then sends the data in the FIFO upstream, retrying until it successfully receives an ACK from the host. Finally, the FIU clears the TX_PACKET_READY bit and asserts a TX_COMPLETE interrupt. Hardware 1. IN token from Host 2. a. If TX Packet Ready = 1, send DATA0/DATA1 b. If TX Packet Ready = 0, send NAK 3. ACK from Host 4. Clear TX Packet Ready Set TX Complete INT 5. Read UISR 6. Read CSR0 Firmware 7. Clear TX COMPLETE in CAR0: a. If more data: fill FIFO, set TX Packet Ready, set DIR in CAR0 b. If no more data: set Force STALL, set DATA END in CAR0 8. Set UIAR[EP0 INTACK] to clear interrupt source Repeat steps 1 through 8 66 AT43USB325 3355A-USB-5/03 AT43USB325 Control Read Status Response State The Function Interface Unit receives an OUT token from the Host with a zero length DATA1 packet. The FIU responds with a NAK until TX_COMPLETE is cleared. The FIU will then ACK the retried OUT token from the Host and assert an RX_OUT interrupt. Hardware 1. OUT token from Host 2. DATA1(0) from Host 3. TX Complete = 0 ? a. If yes, ACK to Host Set RX OUT INT b. If no, NAK to Host 4. Read UISR 5. Read CSR0 Firmware 6. Clear RX OUT, set Data End, set Force Stall in H/FCAR0. Note: A SETUP token will clear Data End, therefore, it is not cleared by FW in case Host retries. 7. Set UIAR[EP0 INTACK] to clear interrupt source Control Write Data Response State The Function Interface Unit receives an OUT token from the Host with a DATA packet. The FIU places the incoming data into the FIFO, issues an ACK to the host, and asserts an RX_OUT interrupt. Hardware 1. OUT token from Host 2. Put DATA0/DATA1 into FIFO 3. ACK to Host 4. Set RX OUT INT 5. Read UISR 6. Read CSR0 7. Read FIFO Firmware 8. Clear RX OUT If last data packet, set Force STALL, set DATA END. 9. Set UIAR[EP0 INTACK] to clear the interrupt source Repeat steps 1 through 9 until last DATA PACKET: 67 3355A-USB-5/03 Control Write Status Response State The Function Interface Unit receives an IN token from the Host. The FIU responds with a zero length DATA1 packet, retrying until it receives an ACK back from the Host. The FIU then asserts a TX_COMPLETE interrupt. Hardware 1. IN token from Host 2. Send DATA1(0) 3. ACK from Host 4. Set TX Complete INT 5. Read UISR 6. Read CSR0 Firmware 7. Clear TX COMPLETE, clear Data End, set Force STALL in CAR0 8. Set UIAR[EP0 INTACK] to clear the interrupt source 68 AT43USB325 3355A-USB-5/03 AT43USB325 Interrupt/Bulk IN Transfers at Function End-point The firmware must first condition the end-point through the End-point Control Register, FENDP1/2/3_CNTR: Set end-point direction: set EPDIR Set interrupt or bulk: EPTYPE = 11 or 10 Enable end-point: set EPEN The Function Interface Unit receives an IN token from the Host. The FIU responds with NAKs until TX_PACKET_READY is set. The FIU then sends the data in the FIFO upstream, retrying until it successfully receives an ACK from the host. Finally, the FIU clears the TX_PACKET_READY bit and asserts a TX_COMPLETE interrupt. 1. Read UISR 2. Read FCSR1/2/3 3. Clear TX_COMPLETE If more data: fill FIFO, set TX Packet Ready Wait for TX_COMPLETE interrupt If no more data: set DATA END in FCAR1/2/3 4. Set UIAR[FEP1/2/3 INTACK] to clear the interrupt source Interrupt/Bulk OUT Transfers at Function End-point EP1, 2 and 3 The firmware must first condition the end-point through the End-point Control Register, FENDP1/2/3_CNTR: Set end-point direction: clear EPDIR Set interrupt or bulk: EPTYPE = 11 or 10 Enable end-point: set EPEN The Function Interface Unit receives an OUT token from the Host with a DATA packet. The FIU places the incoming data into the FIFO, issues an ACK to the host, and asserts an RX_OUT interrupt. 1. Read UISR 2. Read FCSR1/2/3 3. Read FIFO 4. Clear RX_OUT If more data: Wait for RX_OUT interrupt If no more data: set DATA END Set UIAR[FEP1/2/3 INTACK] to clear the interrupt source 69 3355A-USB-5/03 USB Registers The following sections describe the registers of the AT43USB325's USB hub and function units. Reading a bit for which the microcontroller does not have read access will yield a zero value result. Writing to a bit for which the microcontroller does not have write access has no effect. Hub Address Register - HADDR The USB hub contains an address register that contains the hub address assigned by the host. This Hub Address Register must be programmed by the microcontroller once it has received a SET_ADDRESS request from the host. The USB hardware uses the new address only after the status phase of the transaction is completed when the microcontroller has enabled the new address by setting bit 0 of the Global State Register. After power-up or reset, this register will contain the value of 0x00. Hub Address Register - HADDR Bit $1FEF Read/Write Initial Value 7 SAEN R/W 0 6 HADD6 R/W 0 5 HADD5 R/W 0 4 HADD4 R/W 0 3 HADD3 R/W 0 2 HADD2 R/W 0 1 HADD1 R/W 0 0 HADD0 R/W 0 HADDR * Bit 7 - SAEN: Single Address Enable The Single Address Enable bit allows the microcontroller to configure the AT43USB325 into a single address or a composite device. Once this capability is enabled, the hub endpoint 0 (HEP0) is converted from a control endpoint to a programmable function endpoint FEP3; all the endpoints would then operate on the single address. * Bit 6..0 - HADD6...0: Hub Address[6:0] 70 AT43USB325 3355A-USB-5/03 AT43USB325 Function Address Register - FADDR The USB function contains an address register that contains the function address assigned by the host. This Function Address Register must be programmed by the microcontroller once it has received a SET_ADDRESS request from the host and completed the status phase of the transaction. After power up or reset, this register will contain the value of 0x00. Function Address Register - FADDR Bit $1FEE Read/Write Initial Value 7 FEN R/W 0 6 FADD6 R/W 0 5 FADD5 R/W 0 4 FADD4 R/W 0 3 FADD3 R/W 0 2 FADD2 R/W 0 1 FADD1 R/W 0 0 FADD0 R/W 0 FADDR * Bit 7 - FEN: Function Enable The Function Enable bit (FEN) allows the firmware to enable or disable the function endpoints. The firmware will set this bit after receipt of a reset through the hub, SetPortFeature[PORT_RESET]. Once this bit is set, the USB hardware passes to and from the host. When the Single Address bit is set, the condition of FEN is ignored. * Bit 6..0 - FADD6...0: Function Address[6:0] Endpoint Registers Hub Endpoint 0 Control Register - HENDP0_CR Function Endpoint 0 Control Register - FENDP0_CR Bit $1FE7 $24 ($44) Read/Write Initial Value 7 EPEN EPEN R/W 0 6 - - R 0 5 - - R 0 4 - - R 0 3 DTGLE DTGLE R/W 0 2 EPDIR EPDIR R/W 0 1 EPTYPE1 EPTYPE1 R/W 0 0 EPTYPE0 EPTYPE0 R/W 0 HENDP0_CR FENDP0_CR * Bit 7 - EPEN: Endpoint Enable 0 = Disable endpoint 1 = Enable endpoint * Bit 6..4 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 3 - DTGLE: Data Toggle Identifies DATA0 or DATA1 packets. This bit will automatically toggle and requires clearing by the firmware only in certain special circumstances. * Bit 2 - EPDIR: Endpoint Direction 0 = Out 1 = In * Bit 1, 0 - EPTYPE: Endpoint Type These bits must be programmed as 0, 0. 71 3355A-USB-5/03 Function Endpoint 1-3 Control Register - FENDP1-3_CR Bit $1FE4 $1FE3 $1FE2 Read/Write Initial Value 7 EPEN EPEN EPEN R/W 0 6 - - - R 0 5 - - - R 0 4 - - - R 0 3 DTGLE DTGLE DTGLE R/W 0 2 EPDIR EPDIR EPDIR R/W 0 1 EPTYPE1 EPTYPE1 EPTYPE1 R/W 0 0 EPTYPE0 EPTYPE0 EPTYPE0 R/W 0 FENDP1_CR FENDP2_CR FENDP3_CR * Bit 7 - EPEN: Endpoint Enable 0 = Disable endpoint 1 = Enable endpoint * Bit 6..4 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 3 - DTGLE: Data Toggle Identifies DATA0 or DATA1 packets. This bit will automatically toggle and requires clearing by the firmware only in certain special circumstances. * Bit 2 - EPDIR: Endpoint Direction 0 = Out 1 = In * Bit 1, 0 - EPTYPE: Endpoint Type These bits program the type of endpoint. Bit1 0 1 1 Bit0 1 0 1 Type Isochronous Bulk Interrupt 72 AT43USB325 3355A-USB-5/03 AT43USB325 Hub Endpoint 0 Data Register - HDR0 Function Endpoint 0..3 Data Register - FDR0..3 Bit $1FD7 $1FD5 $1FD4 $1FD3 $1FD2 Read/Write Initial Value 7 DATA7 DATA7 DATA7 DATA7 DATA7 R/W 0 6 DATA6 DATA6 DATA6 DATA6 DATA6 R/W 0 5 DATA5 DATA5 DATA5 DATA5 DATA5 R/W 0 4 DATA4 DATA4 DATA4 DATA4 DATA4 R/W 0 3 DATA3 DATA3 DATA3 DATA3 DATA3 R/W 0 2 DATA2 DATA2 DATA2 DATA2 DATA2 R/W 0 1 DATA1 DATA1 DATA1 DATA1 DATA1 R/W 0 0 DATA0 DATA0 DATA0 DATA0 DATA0 R/W 0 HDR0 FDR0 FDR1 FDR2 FDR3 This register is used to read data from or to write data to the Hub Endpoint 0 FIFO. * Bit 7..0 - FDAT7..0: FIFO Data Hub endpoint 1 has a single byte data register instead of a FIFO. This data register contains the hub and port status change bitmap. This data register is automatically updated by the USB hardware and is not accessible by the firmware. The bits in this register when read by the host will be: Bit $ Read/Write Initial Value 7 - R/W 0 6 - R/W 0 5 P5 CS R/W 0 4 P4 CS R/W 0 3 P3 SC R/W 0 2 P2 SC R/W 0 1 P1 SC R/W 0 0 H SC R/W 0 HDR1 * Bit 7,6 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 5 - P5 SC: Port 5 Status Change * Bit 4 - P4 SC: Port 4 Status Change * Bit 3 - P3 SC: Port 3 Status Change * Bit 2 - P2 SC: Port 2 Status Change * Bit 1 - P1 SC: Port 1 Status Change * Bit 0 - H SC: Hub Status Change 73 3355A-USB-5/03 Hub Endpoint 0 Byte Count Register - HBYTE_CNT0 Function Endpoint 0..3 Byte Count Register - FBYTE_CNT0..3 The contents of these registers stores the number of bytes to be sent or that was received by USB Hub and Function endpoints. This count includes the 16-bit CRC. To get the actual byte count of the data, subtract the count in the register by 2. The maximum byte count supported by the AT43USB325 is 8 bytes. Hub endpoint 1 has no byte count register. Bit Hub EP0 $1FCF Function EP0 $1FCD Function EP1 $1FCC Function EP2 $1FCB Function EP3 $1FCA Read/Write Initial Value 7 - - - - - R 0 6 - - - - - R 0 5 BYTCT5 BYTCT5 BYTCT5 BYTCT5 BYTCT5 R 0 4 BYTCT4 BYTCT4 BYTCT4 BYTCT4 BYTCT4 R/W 0 3 BYTCT3 BYTCT3 BYTCT3 BYTCT3 BYTCT3 R/W 0 2 BYTCT2 BYTCT2 BYTCT2 BYTCT2 BYTCT2 R/W 0 1 BYTCT1 BYTCT1 BYTCT1 BYTCT1 BYTCT1 R/W 0 0 BYTCT0 BYTCT0 BYTCT0 BYTCT0 BYTCT0 R/W 0 HBYTE_CNT0 FBYTE_CNT0 FBYTE_CNT1 FBYTE_CNT2 FBYTE_CNT3 * Bit 7..6 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 5..0 - BYTCT5..0: Byte Count - Length of Endpoint Data Packet 74 AT43USB325 3355A-USB-5/03 AT43USB325 Hub Endpoint 0 Service Routine Register - HCSR0 Function Endpoint 0 Service Routine Register - FCSR0 Bit Function EP0 $1FDF Function EP0 $1FDD Read/Write Initial Value 7 - - R 0 6 - - R 0 5 - - R 0 4 - - R 0 3 STALL SENT STALL SENT R 0 2 RX SETUP RX SETUP R 0 1 RX OUT PACKET RX OUT PACKET R 0 0 TX COMPLETE TX COMPLETE R 0 HCSR0 FCSR0 * Bit 7..4 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 3 - STALL SENT The USB hardware sets this bit after a STALL has been sent to the host. The firmware uses this bit when responding to a Get Status[Endpoint] request. It is a read only bit and that is cleared indirectly by writing a one to the STALL_SENT_ACK bit of the Control and Acknowledge Register. * Bit 2 - RX SETUP: Setup Packet Received This bit is used by control endpoints only to signal to the microcontroller that the USB hardware has received a valid SETUP packet and that the data portion of the packet is stored in the FIFO. The hardware will clear all other bits in this register while setting RX SETUP. If interrupt is enabled, the microcontroller will be interrupted when RX SETUP is set. After the completion of reading the data from the FIFO, firmware should clear this bit by writing a one to the RX_SETUP_ACK bit of the Control and Acknowledge Register. * Bit 1 - RX OUT PACKET The USB hardware sets this bit after it has stored the data of an OUT transaction in the FIFO. While this bit is set, the hardware will NAK all OUT tokens. The USB hardware will not overwrite the data in the FIFO except for an early set-up. RX OUT Packet is used for the following operations: 1. Control write transactions by a control endpoint. 2. OUT transaction with DATA1 PID to complete the status phase of a control endpoint. Setting this bit causes an interrupt to the microcontroller if the interrupt is enabled. FW clears this bit after the FIFO contents have been read by writing a one to the RX_OUT_PACKET_ACK bit of the Control and Acknowledge Register. * Bit 0 - TX COMPL: Transmit Completed This bit is used by a control endpoint hardware to signal to the microcontroller that it has successfully completed certain transactions. TX Complete is set at the completion of a: 1. Control read data stage. 2. Status stage without data stage. 3. Status stage after a control write transaction. This bit is read only and is cleared indirectly by writing a one to the TX_COMPLETE_ACK bit of the Control and Acknowledge Register. 75 3355A-USB-5/03 Hub Endpoint 0 Control and Acknowledge Register - HCAR0 Function Endpoint 0 Control and Acknowledge Register - FCAR0 Bit Hub EP0 $1FA7 7 6 DATA END 5 FORCE STALL 4 TX PACKET READY TX PACKET READY R/W 0 3 STALL_ SENT_ ACK STALL_ SENT_ ACK R/W 0 2 RX_ SETUP_ ACK RX_ SETUP_ ACK R/W 0 1 RX_OUT_ PACKET_ ACK RX_OUT_ PACKET_ ACK R/W 0 0 TX_ COMPLETE_ ACK TX_ COMPLETE_ ACK R/W 0 DIR HCAR0 Function EP0 $1FDD Read/Write Initial Value DIR DATA END R/W 0 FORCE STALL R/W 0 FCAR0 R/W 0 * Bit 7 - DIR: Control transfer direction It is set by the microcontroller firmware to indicate the direction of a control transfer to the USB hardware. The FW writes to this bit location after it receives an RX SETUP interrupt. The hardware uses this bit to determine the status phase of a control transfer. 0 = control write or no data stage 1 = control read * Bit 6 - DATA END When set to 1 by firmware, this bit indicate that the microcontroller has either placed the last data packet in FIFO, or that the microcontroller has processed the last data packet it expects from the Host. This bit is used by control endpoints only together with bit 4 (TX Packet Ready) to signal the USB hardware to go to the STATUS phase after the packet currently residing in the FIFO is transmitted. After the hardware completes the STATUS phase it will interrupt the microcontroller without clearing this bit. * Bit 5 - FORCE STALL This bit is set by the microcontroller to indicate a stalled endpoint. The hardware will send a STALL handshake as a response to the next IN or OUT token, or whenever there is a control transfer without a Data Stage. The microcontroller sets this bit if it wants to force a STALL. A STALL is sent if any of the following condition is encountered: 1. An unsupported request is received. 2. The host continues to ask for data after the data is exhausted. 3. The control transfer has no data stage. * Bit 4 - TX PACKET READY: Transmit Packet Ready When set by the firmware, this bit indicates that the microcontroller has loaded the FIFO with a packet of data. This bit is cleared by the hardware after the USB Host acknowledges the packet. For ISO endpoints, this bit is cleared unconditionally after the data is sent. This bit is used for the following operations: 1. Control read transactions by a control endpoint. 2. IN transactions with DATA1 PID to complete the status phase for a control endpoint, when this bit is zero but Data End set high (bit 4). 3. By a BULK IN or ISO IN or INT IN endpoint. The microcontroller should write into the FIFO only if this bit is cleared. After it has completed writing the data, it should set this bit. This data can be of zero length. 76 AT43USB325 3355A-USB-5/03 AT43USB325 Hardware clears this bit after it receives an ACK. If the interrupt is enabled and if the TX Complete bit is set, clearing the TX Packet Ready bit by the hardware causes an interrupt to the microcontroller. * Bit 3 - STALL_SENT_ACK: Acknowledge Stall Sent Interrupt Firmware sets this bit to clear STALL SENT, CSR bit 3. The 1 written in the CSRACK3 bit is not actually stored and thus does not have to be cleared. * Bit 2 - RX_SETUP_ACK: Acknowledge RX SETUP Interrupt Firmware sets this bit to clear RX SETUP, CSR bit2. The 1 written in the CSRACK2 bit is not actually stored and thus does not have to be cleared. * Bit 1 - RX_OUT_PACKET_ACK: Acknowledge RX OUT PACKET Interrupt Firmware sets this bit to clear RX OUT PACKET, CSR bit1. The 1 written in the CSRACK1 bit is not actually stored and thus does not have to be cleared. * Bit 0 - TX_COMPLETE_ACK: Acknowledge TX COMPLETE Interrupt Firmware sets this bit to clear TX COMPLETE, CSR bit0. The 1 written in the CSRACK0 bit is not actually stored and thus does not have to be cleared. Function Endpoint 1,2,3 Service Routine Register - FCSR1,2,3 Bit Function EP1 $1FDC Function EP2 $1FDB Function EP3 $1FDA Read/Write Initial Value 7 - - - R 0 6 - - - R 0 5 - - - R 0 4 - - - R 0 3 STALL SENT STALL SENT STALL SENT R 0 2 - - - R 0 1 RX OUT PACKET RX OUT PACKET RX OUT PACKET R 0 0 TX COMPLETE TX COMPLETE TX COMPLETE R 0 FCSR1 FCSR2 FCSR3 * Bit 7..4 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 3 - STALL SENT The USB hardware sets this bit after a STALL has been sent to the host. The firmware uses this bit when responding to a Get Status[Endpoint] request. It is a read only bit and that is cleared indirectly by writing a one to the STALL_SENT_ACK bit of the Control and Acknowledge Register. * Bit 2 - Reserved This bit is reserved in the AT43USB325 and will read as zero. * Bit 1 - RX OUT PACKET The USB hardware sets this bit after it has stored the data of an OUT transaction in the FIFO. While this bit is set, the hardware will NAK all OUT tokens. The USB hardware will not overwrite the data in the FIFO except for an early set-up. RX OUT Packet is used by a BULK OUT or ISO OUT or INT OUT endpoint. Setting this bit causes an interrupt to the microcontroller if the interrupt is enabled. FW clears this bit after the FIFO contents have been read by writing a one to the RX_SETUP_ACK bit of the Control and Acknowledge Register. * Bit 0 - TX COMPLETE: Transmit Completed This bit is used by the endpoint hardware to signal to the microcontroller that the IN transaction was completed successfully. This bit is read only and is cleared indirectly by writing a one to the TX_COMPLETE_ACK bit of the Control and Acknowledge Register. 77 3355A-USB-5/03 Function Endpoint 1,2,3 Control and Acknowledge Register - FCAR1,2,3 Bit Function EP1 $1FA4 7 - 6 DATA END DATA END DATA END R/W 0 5 FORCE STALL FORCE STALL FORCE STALL R/W 0 4 TX PACKET RDY TX PACKET RDY TX PACKET RDY R/W 0 3 STALL_SENTACK STALL_SENTACK STALL_SENTACK R/W 0 2 - 1 RX_OUT_PACKET _ACK RX_OUT_PACKET _ACK RX_OUT_PACKET _ACK R/W 0 0 TX_COMPLETE_ ACK TX_COMPLETE_ ACK TX_COMPLETE_ ACK R/W 0 FCAR1 Function EP2 $1FA3 - - FCAR2 Function EP3 $1FA2 Read/Write Initial Value - R 0 - R 0 FCAR3 * Bit 7 - Reserved This bit is reserved in the AT43USB325 and will read as zero. * Bit 6 - DATA END When set to 1 by firmware, this bit indicate that the microcontroller has either placed the last data packet in FIFO, or that the microcontroller has processed the last data packet it expects from the Host. * Bit 5 - FORCE STALL This bit is set by the microcontroller to indicate a stalled endpoint. The hardware will send a STALL handshake as a response to the next IN or OUT token. The microcontroller sets this bit if it wants to force a STALL. A STALL is send if the host continues to ask for data after the data is exhausted. * Bit 4 - TX PACKET RDY: Transmit Packet Ready When set by the firmware, this bit indicates that the microcontroller has loaded the FIFO with a packet of data. This bit is cleared by the hardware after the USB Host acknowledges the packet. For ISO endpoints, this bit is cleared unconditionally after the data is sent. The microcontroller should write into the FIFO only if this bit is cleared. After it has completed writing the data, it should set this bit. This data can be of zero length. The hardware clears this bit after it receives an ACK. If the interrupt is enabled and if the TX Complete bit is set, clearing the TX Packet Ready bit by the hardware causes an interrupt to the microcontroller. * Bit 3 - STALL_SENT_ACK: Acknowledge Stall Sent Interrupt Firmware sets this bit to clear STALL SENT, CSR bit 3. The 1 written in the CSRACK3 bit is not actually stored and thus does not have to be cleared. * Bit 2 - Reserved This bit is reserved in the AT43USB325 and will read as zero. * Bit 1 - RX_OUT_PACKET_ACK: Acknowledge RX OUT PACKET Interrupt Firmware sets this bit to clear RX OUT PACKET, CSR bit1. The 1 written in the CSRACK1 bit is not actually stored and thus does not have to be cleared. * Bit 0 - TX_COMPLETE_ACK: Acknowledge TX COMPLETE Interrupt Firmware sets this bit to clear TX COMPLETE, CSR bit0. The 1 written in the CSRACK0 bit is not actually stored and thus does not have to be cleared. 78 AT43USB325 3355A-USB-5/03 AT43USB325 USB Hub The hub in a USB system provides for the electrical interface between USB devices and the host. The major functions that the hub must supports are: * * * * * Connectivity Power management Device connect and disconnect Bus fault detection and recovery Full speed and low speed device support A hub consists of two major components: a hub repeater and a hub controller. The hub repeater is responsible for: * * * * * * * * Providing upstream connectivity between the selected device and the Host Managing connectivity setup and tear-down Handling bus fault detection and recovery Detecting connect/disconnect on each port Hub enumeration Providing configuration information to the host Providing status of each port to the host Controlling each port per host command The Hub Controller is responsible for: The first two tasks of the hub are similar to that of a USB function and are described in detail in the following section. The descriptions will cover the features of the AT43USB325's hub and how to program it to make a USB-compliant hub. Control transactions for the hub control endpoint proceed exactly the same way as those described for the embedded function. The operation of the hub's endpoint 1 is fully implemented in the hardware and does not need any firmware support. Any status changes within the hub will automatically update hub endpoint 1, which will be sent to the host at the next IN token that is addressed to it. If no change has occurred, the interrupt endpoint will respond with a NAK. 79 3355A-USB-5/03 Hub General Registers Global State Register - GLB_STATE Bit $1FFB Read/Write Initial Value 7 - R 0 6 KB INT EN R 0 5 - R 0 4 SUSP FLG R 0 3 RESUME FLG R 0 2 RMWUPE R/W 0 1 CONFG R/W 0 0 HADD EN R/W 0 GLB_STATE * Bit 7 - Reserved Bit This bit is reserved in the AT43USB325 and will read as zero. * Bit 6 - KB INT EN: Keyboard Interrupt Enable The firmware must set this bit to a 1 before entering suspend to allow remote wakeup when any key depression is detected in the suspended state. * Bit 5 - Reserved Bit This bit is reserved in the AT43USB325 and will read as zero. * Bit 4 - SUSP FLG: Suspend Flag This bit is set to 1 while the USB hardware is in the suspended state. This bit is a firmware read only bit. It is set and cleared by the USB hardware. * Bit 3 - RESUME FLGL Resume Flag When the USB hardware receives a resume signal from the upstream device it sets this bit. This bit will stay set until the USB hardware completes the downstream resume signaling. This bit is a firmware read only bit. It is set and cleared by the USB hardware. * Bit 2 - RMWUPE: Remote Wakeup Enable This bit is set if the host enables the hub's remote wakeup feature. * Bit 1 - CONFG: Configured This bit is set by firmware after a valid SET_CONFIGURATION request is received. It is cleared by a reset or by a SET_CONFIGURATION with a value of 0. * Bit 0 - HADD EN: Hub Address Enabled This bit is set by firmware after the status phase of a SET_ADDRESS request transaction so the hub will use the new address starting at the next transaction. 80 AT43USB325 3355A-USB-5/03 AT43USB325 Hub Status Register In the AT43USB325 overcurrent detection and port power switch control output processing is done in firmware. The hardware is designed so that various types of hubs are possible just through firmware modifications. 1. Hub local power status, bits 0 and 2, are optional features and apply to hubs that report on a global basis. If this feature is not used, both these bits should be programmed to 0. To use this feature, the firmware needs to know the status of the local power supply, which requires an input pin and extra internal or external circuitry. 2. Hub overcurrent status, bits 1 and 3, apply to self powered hubs with bus powered SIE only, or hubs that are programmable as self/bus powered. The firmware should clear these two bits to 0. The firmware uses bits 1 and 3 to generate bit 0 of the Hub and Port Status Change Bitmap which is transmitted through the Hub Endpoint1 Data Register. Bit 0 of this register is a 1 whenever bit 1 or 3 of HSTATR is a 1. Hub Status Register - HSTR Bit $1FC7 Read/Write Initial Value 7 - R 0 6 - R 0 5 - R 0 4 - R 0 3 OVLSC R/W 0 2 LPSC R/W 0 1 OVI R/W 0 0 LPS R/W 0 HSTR * Bit 7..4 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 3 - OVLSC: Overcurrent Status Change 0 = No change has occurred on Overcurrent Indicator 1 = Overcurrent Indicator has changed * Bit 2 - LPSC: Hub Local Power Status Change 0 = No change has occurred on Local Power Status 1 = Local Power Status has changed * Bit 1 - OVI: Overcurrent Indicator 0 = All power operations normal 1 = An overcurrent exist on a hub wide basis * Bit 0 - LPS: Hub Local Power Status 0 = Local power supply is good 1 = Local power supply is lost (inactive) 81 3355A-USB-5/03 Hub Port Control Register - HPCON Bit $1FC5 Read/Write Initial Value 7 - R 0 6 HPCON2 R/W 0 5 HPCON1 R/W 0 4 HPCON0 R/W 0 3 - R 0 2 HPADD2 R/W 0 1 HPADD1 R/W 0 0 HPADD0 R/W 0 HPCON * Bit 7 - Reserved This bits is reserved in the AT43USB325 and will read as zero. * Bit 6..4 - HPCON2..0: Hub Port Control Command These bits are written by firmware to control the port states upon receipt of a Host request. Bit6 0 0 0 0 1 Bit5 0 0 1 1 0 Bit4 0 1 0 1 0 Action Disable port Enable port Reset and enable port Suspend port Resume port Disable Port = ClearPortFeature(PORT_ENABLE) Action: USB hardware places addressed port in disabled state. Port 1 is placed in disabled state by firmware. Enable Port = SetPort Feature(PORT_ENABLE) Action: USB hardware places addressed port in enabled state. Firmware is responsible for placing Port 1 in enabled state. Reset and Enable Port = SetPort Feature(PORT_RESET) Action: USB hardware drives reset signaling through addressed port. USB hardware and firmware resets their embedded function registers to the default state. Suspend Port = SetPortFeature(PORT_SUSPEND) Action: USB hardware places port in idle state and stops propagating traffic through the addressed port. Firmware places Port 1 in suspend state by disabling its endpoints and placing the peripheral function in its low power state. Resume Port = ClearPortFeature(PORT_SUSPEND) Action: USB hardware sends resume signaling to addressed port and then enables port. Firmware takes the embedded function out of the suspend state and enables Port 1's endpoints. * Bit 3 - Reserved This bits is reserved in the AT43USB325 and will read as zero. * Bit 2..0 - HPCON2..0: Hub Port Address 82 AT43USB325 3355A-USB-5/03 AT43USB325 These bits define which port is being addressed for the command defined by bits [2:0]. Bit2 1 1 0 0 Bit1 0 0 1 1 Bit0 1 0 1 0 Port addresses Port5 Port4 Port3 Port2 Selective Suspend and Resume The host can selectively suspend and resume a port through the Set Port Feature (PORT_SUSPEND) and Clear Port Feature (PORT_SUSPEND). A port enters the suspend state after the microcontroller interprets the suspend request and sets the appropriate bits of the Hub Port Control Register, HPCON. From this point on he hub repeater hardware is responsible for proper actions in placing Ports 2:5 in the suspend mode. For Port 1, the embedded function port, the hardware will stop responding to any normal bus traffic, but the microcontroller firmware must place all external circuitry associated with the function in the low-power state. A port exits from the suspend state when the hub receives a Clear Port Feature (PORT_SUSPEND) or Set Port Feature (PORT_RESET). If the Clear Port Feature (PORT_SUSPEND) is directed towards Ports 2:5, the USB hardware drives a "K" downstream for at least 20 ms followed by a low speed EOP. It then places the port in the enabled state. A Clear Port Feature (PORT_SUSPEND) to Port 1 (the embedded function) causes the firmware to wait 20 ms, take the embedded function out of the suspended state and then enable the port. The ports can also exit from the suspended state through a remote wakeup if this feature is enabled. For Ports 2:5, this means detection of a connect/disconnect or an upstream directed J to K signaling. Remote wakeup for the embedded function is initiated through a key depression which triggers a KB INT. 83 3355A-USB-5/03 Hub Port Status Register The bits in this register are used by the microcontroller firmware when reporting a port's status through the Port Status Field, wPortStatus. Bits 3 (POCI) and 5 (PPSTAT) are used by the USB hardware and are the only two bits that the firmware should set or clear. All other bits should not be modified by the firmware. Hub Port Status Register - HPSTAT1:5 Bit Port1 $1FB8 Port2 $1FB9 Port3 $1FBA Port4 $1FBB Port5 $1FBC Read/Write Initial Value 7 - - - - - R 0 6 LSP LSP LSP LSP LSP R 0 5 PPSTAT PPSTAT PPSTAT PPSTAT PPSTAT R/W 0 4 PRSTAT PRSTAT PRSTAT PRSTAT PRSTAT R 0 3 POCI POCI POCI POCI POCI R/W 0 2 PSSTAT PSSTAT PSSTAT PSSTAT PSSTAT R 0 1 PESTAT PESTAT PESTAT PESTAT PESTAT R 0 0 PCSTAT PCSTAT PCSTAT PCSTAT PCSTAT R 0 HPSTAT1 HPSTAT2 HPSTAT3 HPSTAT4 HPSTAT5 * Bit 7 - Reserved This bit is reserved in the AT43USB325 and will read as zero. * Bit 6 - LSP: Low-speed Device Attached 0 = Full-speed device attached to this port 1 = Slow-speed device attached to this port Set to 0 for Port 1 (full-speed only). Set and cleared by the hardware upon detection of device at EOF2. * Bit 5 - PPSTAT: Port Power Status 0 = Port is powered OFF 1 = Port is powered ON Set to 1 for Port 1. Set and cleared based on present status of port power. * Bit 4 - PRSTAT: Port Reset Status 0 = Reset signaling not asserted 1 = Reset signaling asserted Set and cleared by the hardware as a result of initiating a port reset by Port Control Register. * Bit 3 - POCI: Port Overcurrent Indicator 0 = Power normal 1 = Overcurrent exist on port Set to 0 for Port 1. Set and cleared by firmware upon detection of an overcurrent or removal of an overcurrent. * Bit 2 - PSSTAT: Port Suspend Status 0 = Port not suspended 1 = Port suspended Set and cleared by the hardware as controlled through Port Control Register. * Bit 1 - PESTAT: Port Enable Status 0 = Port is disabled 84 AT43USB325 3355A-USB-5/03 AT43USB325 1 = Port is enabled Set and cleared by the hardware as controlled through Port Control register. * Bit 0 - PCSTAT: Port Connect Status 0 = No device on this port 1 = Device present on this port Set to 1 for Port 1. Set and cleared by the hardware after sampling of connect status at EOF2. Overcurrent Detect Register - UOVCER Bit $1FF2 Read/Write Initial Value 7 - R 0 6 - R 0 5 - R 0 4 - R 0 3 - R 0 2 OVC2 R/W 0 1 - R 0 0 - R 0 UOVCER * Bit 7..3 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 2 - OVC 2 Setting this bit enables the hub to detect an overcurrent on a port while the hub is in the suspend state. The overcurrent condition is signalled by a 1 to 0 transition at PD0. * Bit 1, 0 - Reserved These bits are reserved in the AT43USB325 and will read as zero. Hub Port State Register - HPSTAT2...5 Bit Port2 $1FA9 Port3 $1FAA Port4 $1FAB Port5 $1FAC Read/Write Initial Value 7 - - - - R 0 6 - - - - R 0 5 - - - - R 0 4 - - - - R 0 3 - - - - R 0 2 - - - - R 0 1 DPSTATE DPSTATE DPSTATE DPSTATE R 0 0 DMSTATE DMSTATE DMSTATE DMSTATE R 0 PSTATE2 PSTATE3 PSTATE4 PSTATE5 These registers contain the state of the ports' DP and DM pins, which will be sent to the host upon receipt of a GetBusState request. * Bit 7..2 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 1 - DPSTATE: DPlus State Value of DP at last EOF. Set and cleared by hardware at EOF2. Set to 1 for Port 1. * Bit 0 - DMSTATE: DMinus State Value of DM at last EOF. Set and cleared by hardware at EOF2. Set to 0 for Port 1. 85 3355A-USB-5/03 Hub Port Status Change Register - PSCR1..5 Bit Port1 $1FB0 Port2 $1FB1 Port3 $1FB2 Port4 $1FB3 Port5 $1FB4 Read/Write Initial Value 7 - - - - - R 0 6 - - - - - R 0 5 - - - - - R 0 4 RSTSC RSTSC RSTSC RSTSC RSTSC R 0 3 POCIC POCIC POCIC POCIC POCIC R 0 2 PSSC PSSC PSSC PSSC PSSC R 0 1 PESC PESC PESC PESC PESC R 0 0 PCSC PCSC PCSC PCSC PCSC R 0 PSCR1 PSCR2 PSCR3 PSCR4 PSCR5 The microcontroller firmware uses the bits in this register to monitor when a port status change has occurred, which then gets reported to the host through the Port Change Field wPortChange. Except for bit 3, the Port Overcurrent Indicator Change, the bits in this register are set by the USB hardware. Otherwise, the firmware should only clear these bits. * Bit 7..5 - Reserved These bits are reserved in the AT43USB325 and will read as zero. * Bit 4 - RSTSC: Port Reset Status Change 0 = No change 1 = Reset complete This bit is set by the USB hardware after it completes RESET signaling which is initiated when the Reset and Enable Port command is detected at the Port Control Register, HPCON. The firmware sends this command when it decodes a SetPortFeature(PORT_RESET) request from the host. At EOF2 after the hardware completes the port reset, the hardware sets the Port Enable Status bit and clears the Port Reset Status bit of the Hub Port Status Register, HPSTAT. Cleared by firmware, ClearPortFeature(PORT_RESET). * Bit 3 - POCIC: Port Overcurrent Indicator Change 0 = No change has occurred on Overcurrent Indicator 1 = Overcurrent Indicator has changed This bit is relevant to hubs with individual overcurrent reporting only. The firmware sets this bit as a result of detecting overcurrent at the ports OVC# pin. The firmware clears bit through ClearPortFeature(PORT_OVER_CURRENT). For Port 1, this bit is always cleared. * Bit 2 - PSSC: Port Suspend Status Change 0 = No change 1 = Resume completed Port 2, 3 set by hardware upon completion of firmware initiated resume process. Port 1 set by firmware 20 ms after the next EOF2 after completion of resume process. RESUME signaling is initiated through global resume, selective resume and remote wakeup. Cleared by firmware via host request ClearPortFeature(PORT_SUSPEND). * Bit 1 - PESC: Port Enable/Disable Status Change 0 = No change has occurred on Port Enable/Disable Status 86 AT43USB325 3355A-USB-5/03 AT43USB325 1 = Port Enable/Disable status has changed Set by hardware due to babble, physical disconnect or overcurrent except for Port 1 in which case it is set by hardware at EOF2 due to hardware events. Cleared by firmware via Host request ClearPortFeature(PORT_ENABLE). * Bit 0 - PCSC: Port Connect Status Change 0 = No change has occurred on Current Connect Status 1 = Current Connect Status has changed This bit is set by hardware at EOF2 after it detects a connect or disconnect at a port, except for Port 1. Hardware sets this bit for Port 5 after a hub reset. Cleared by firmware via Host request ClearPortFeature(PORT_CONNECTION). Hub and Port Power Management Overcurrent protection and power switching are required for the external downstream ports only. In the AT43USB325, these tasks are completely programmable. This means that any type of hub is achievable with the AT43USB325: self-powered or bus-powered hubs, per port or global overcurrent protection, individual or ganged port power switching. The use of the MCU's GPIO pins are required to interface to the external power supply monitoring and switching. The on-chip hardware of the AT43USB325 contains the circuitry to handle all the possible combinations of port power management tasks. The firmware defines the exact configuration. Overcurrent Sensing The AT43USB325 is capable of detecting overcurrent during active operation only, or during any condition even when the hub is in the suspended state. When overcurrent in the active state only is desired, any GPIO pin of the AT43USB325 can be used to sense and the overcurrent condition. Control of the condition must be performed by the firmware. If overcurrent detection under any condition is desired, then specific GPIO pins must be used to sense the overcurrent and the proper bit(s) of UOVCER set. In Global Overcurrent Protection mode, overcurrent sensing must be routed to GPIO PD0. In Individual Port Overcurrent Protection mode Port2 and Port 3 overcurrent sensing must be assigned to GPIO PD0 and PD1. In the following description, it is assumed that overcurrent protection is required under any condition. 1. Global Overcurrent Protection - In this mode, the Port Overcurrent Indicator and Port Overcurrent Indicator Change should be set to 0's. For the AT43USB325 an external solid state switch, such as the Micrel MIC2025-2, is required to switch power to the external USB ports. The FLG output of the switch should be connected to PD0. When an overcurrent occurs, FLG is asserted and the firmware should set the Hub Overcurrent Indicator and Hub Overcurrent Indicator Change and switch off power to all external downstream ports. The hub status change is reported on the next IN token through the hub's interrupt endpoint, Endpoint1. 2. Individual Port Overcurrent Protection - The Hub Overcurrent Indicator and Hub Overcurrent Indicator Change bits should be set to 0's. One MIC2026-2 is required for the two USB ports. The FLG output of the MIC2026-2 associated with Port2 should be connected to GPIO PD0 and the other FLG output to PD1. An overcurrent is indicated by assertion of FLG. The firmware sets the corresponding port's Overcurrent Indicator and the Overcurrent Indicator Change bits and switches off power to the port. At the next IN token from the Host, the AT43USB325 reports the port status change through the hub's Endpoint1. Port Power Switching 1. Gang Power Switching - One of the microcontroller GPIO pins, PWRN, must be programmed as an output to control the external switch such as the MIC2025-2. Switch ON is requested by the USB Host through the SetPortFeature(PORT_POWER) request. Switch OFF is executed upon receipt of a ClearPortFeature(PORT_POWER) 87 3355A-USB-5/03 or upon detecting an overcurrent condition. The firmware clears the Power Control Bit. Only if all of the Power Control Bits of ports 2 and 3 are cleared should the firmware deassert the PWRN pin. 2. Individual Power Switching - Two microcontroller GPIO pins, PWR2N and PWR3N, must be assigned for each USB port to control the external switch such as the MIC2026-2. Each of the Power Control Bits controls one PWRxN. 3. Multiple Ganged Overcurrent Protection - Overcurrent sensing is grouped physically into one or more gangs, but reported individually. Figure 17 shows a simplified diagram of a power management circuit of an AT43USB325 based hub design with global overcurrent protection and ganged power switching. Figure 17. Port Power Management BUS_POWER GND GND VCC AT43USB325 PWRN OVCN PORT2_POWER PORT2_GND PORT3_POWER CTL IN FLG OUT SWITCH PORT3_GND PORT4_POWER PORT4_GND PORT5_POWER PORT5_GND Suspend and Resume The AT43USB325 enters suspend only when requested by the USB host through bus inactivity for at least 3 ms. The USB hardware would detect this request, sets the GLB_SUSP bit of SPRSR, Suspend/Resume Register, and interrupts the microcontroller if the interrupt is enabled. The microcontroller should shut down any peripheral activity and enter the Power Down mode by setting the SE and SM bits of MCUCR and then executes the SLEEP instruction. The USB hardware shuts off the oscillator and PLL. 88 AT43USB325 3355A-USB-5/03 AT43USB325 Global Resume Global resume is signaled by a J to K state change on Port0. The USB hardware enables the oscillator/PLL, propagates the RESUME signaling, and sets the RSM bit of the SPRSR, which generates an interrupt. The microcontroller starts executing where it left off and services the interrupt. As part of the ISR, the firmware clears the GLB_SUSP bit. While the AT43USB325 is in global suspend, resume signaling is also possible through remote wakeup if the remote wakeup feature is enabled. Remote wakeup is defined as a port connect, port disconnect or resume signaling received at a downstream port or, in case of the embedded function, through an external interrupt. A remote wakeup initiated at a downstream port is similar in many respects to a global resume. The USB hardware enables the oscillator/PLL, propagates the RESUME signaling, and sets the RSM bit of the SPRSR which generates an interrupt. The microcontroller starts executing where it left off and services the interrupt. As part of the ISR, the firmware clears the GLB_SUSP bit. A remote wakeup from the embedded function is initiated through INT0 or the external interrupt, INT1, which enables the oscillator/PLL and the USB hardware. The USB hardware drives RESUME signaling and sets the FRMWUP and RSM bits of SPRSR which generates an interrupt to the microcontroller. The microcontroller starts executing where it left off and services the interrupt. As part of the ISR, the firmware clears the GLB SUSP bit. At completion of RESUME signaling, the USB hardware sets the Port Suspend Status Change bits of the Hub Port Status Change Registers. Selective Suspend and Resume Suspend and Resume Process Global Suspend The Host stops sending packets, the hardware detects this as global suspend signaling and stops all downstream signaling. Finally, the hardware asserts the GLB_SUSP interrupt. Hardware 1.Host stops sending packets 2. Global suspend signaling detected 3. Stop downstream signaling 4. Set GBL SUS bit interrupt 5. Shut down any peripheral activity 6. Set Sleep Enable and Sleep Mode bits of MCUCR 7. Set GPIO to low power state if required 8. Set UOVCER bit 2 9. Execute SLEEP instruction 10. SLEEP bit detected 11. Shut off oscillator Firmware See section on Hub Port Control Register, HPCON. Remote Wakeup 89 3355A-USB-5/03 Global Resume The Host resumes signaling, the hardware detects this as global resume and propagates this signaling to all downstream ports. Finally, the hardware enables the oscillator and asserts the RSM interrupt. Hardware 1.Host resumes signaling 2. Resume signaling detected 3. Propagate signaling downstream 4. Enable oscillator 5. Set RSM bit interrupt 6. Reset RSM and GBL SUSP bits 7. Restore GPIO states if required 8. Clear UOVCER bit 2 9. Enable peripheral activity Firmware Remote Wake-up, Downstream Ports The hardware detects a connect/disconnect/port resume and propagates resume signaling upstream. Finally, the hardware enables the oscillator and asserts the RSM interrupt. Hardware 1. Connect/disconnect/port resume detected 2. Propagate resume signaling 3. Enable Oscillator 4. Set RSM bit interrupt 5. Reset RSM and GBL SUSP bits 6. Restore GPIO states if required 7. Clear UOVCER bit 2 8. Enable peripheral activity Firmware Remote Wake-up, Embedded Function The hardware detects an INT0/INT1 and propagates resume signaling upstream. Finally, the hardware enables the oscillator and asserts the RSM and FRWUP interrupts. Hardware Firmware 1.External event activates INT0/INT1 2. Propagate resume signaling 3. Enable Oscillator 4. Set RSM and FRMWUP bits interrupt 5. Clear GLB SUSP, RSM, FRMWUP bits 6. Restore GPIO states if required 7. Clear UOVCER bit 2 8. Enable peripheral activity 90 AT43USB325 3355A-USB-5/03 AT43USB325 Selective Suspend, Downstream Ports Hardware Firmware 1. Set or Clear Port Feature PORT_SUSPEND decoded 2. Write HPCON[2:0] and HPADD[2:0] bits 3. Suspend or resume port per command Selective Suspend, Embedded Function Hardware Firmware 1. Set Port Feature PORT_SUSPEND decoded 2. Disable Port 1's endpoints 3. Set GPIO to low power state if required Selective Resume, Embedded Function Hardware Firmware 1. Clear Port Feature PORT_SUSPEND decoded 2. Clear Port 1 suspend status bit 3. Restore GPIO states if required 4. Wait 23 ms, then set enable status bit and suspend change bit 5. Enable Port 1 endpoints 6. Send updated port status at next IN to endpoint1 91 3355A-USB-5/03 Electrical Specification Absolute Maximum Ratings Stresses beyond those listed below may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 24. Absolute Maximum Ratings Symbol VCC5 VI VO TO TS Note: Parameter 5V Power Supply DC input voltage DC output voltage Operating temperature Storage temperature VCEXT is the voltage at CEXT1, CEXT2. -0.3V -0.3 -40 -65 Condition Min Max 5.5 VCEXT+0.3 4.6 max VCEXT+0.3 4.6 max +125 +150 Unit V V V C C DC Characteristics The values shown in this table are valid for TA = 0C to 85C, VCC = 4.4 to 5.25V, unless otherwise noted. Table 25. Power Supply Symbol VCC ICC ICCS Parameter 5V Power Supply 5V Supply Current Suspended Device Current Condition Min 4.4 Max 5.25 40 600 Unit V mA uA 92 AT43USB325 3355A-USB-5/03 AT43USB325 Table 26. USB Signals: DPx, DMx Symbol VIH VIHZ VIL VDI VCM VOL1 VOH1 VCRS VIN Parameter Input Level High (driven) Input Level High (floating) Input Level Low Differential Input Sensitivity Differential Common Mode Range Static Output Low Static Output High Output Signal Crossover Input Capacitance RL of 1.5 k to 3.6V RL of 15 k to GND 2.8 1.3 DPx and DMx 0.2 0.8 2.5 0.3 3.6 2.0 20 Condition Min 2.0 2.7 0.8 Max Unit V V V V V V V V pF Table 27. PA, PB, PC, PD, PE, PF Symbol VOL2 RPU VIL3 VIH3 VIL4 VIH4 VOL4 VOH4 C Note: Parameter Output Low Level, PA, PB, PE[0:3] PC Pull-up resistor current Input Low Level, PC Input High Level, PC Input Low Level, PD[0,1] Input High Level, PD[0,1] Output Low Level, PD[0,1] Output High Level, PD[0,1] Input/Output capacitance IOL = 4 mA IOH = 4 mA 1 MHz 0.7 VCEXT 10 0.7 VCEXT 0.3 VCEXT 0.7 VCEXT 0.3 VCEXT Condition IOL = 4 mA V=0 90 Min Max 0.5 280 0.3 VCEXT Unit V A V V V V V V pF VCEXT is the voltage at CEXT1, CEXT2. 93 3355A-USB-5/03 Table 28. Oscillator Signals: XTAL1, XTAL2 Symbol VLH VHL CX1 CX2 C12 tSU DL Note: Parameter OSC1 switching level OSC1 switching level Input capacitance, XTAL1 Output capacitance, XTAL2 OSC1/2 capacitance Start-up time Drive level XTAL2 must not be used to drive other circuitry. 6 MHz, fundamental Condition Min 0.47 0.67 Max 1.20 1.44 10 10 5 2 50 Unit V V pF pF pF ms W AC Characteristics Table 29. SEEPROM SPI Timing Symbol fSCK tRO, tFO tCSS tCSH tSU tH tHO tV Parameter SCK Clock Frequency 50% duty cycle Output Rise Time, Fall Time -5 SSN Setup Time SSN Hold Time Data IN Setup Time Data In Hold Time Output Hold Time Output Valid 0 0 10 2 0 10 5 20 20 ns ns ns ns ns ns ns Condition Min 333 10 Max 333 10 Unit ns ns Figure 18. Synchronous Data Timing SSN VIH VIL tCSS VIH SCK V IL tWH tWL tCSH tCS VIH MOSI V IL tSU VALID IN tH VOH MISO VOL tV HI-Z tH0 tDIS HI-Z 94 AT43USB325 3355A-USB-5/03 AT43USB325 Table 30. USB Driver Characteristics, Full Speed Operation Symbol TR TF TRFM ZDRV Note: Parameter Rise time Fall time TR/TF matching Driver output resistance(1) Steady state drive Condition CL = 50 pF CL = 50 pF Min 4 4 90 28 Max 20 20 110 44 Unit ns ns % 1. With external 27 series resistor. Figure 19. Full-speed Load RS TxD+ CL RS TxDCL CL = 50 pF Table 31. USB Driver Characteristics, Low-speed Operation Symbol TR TF TRFM Parameter Rise time Fall time TR/TF matching Condition CL = 200 - 600 pF CL = 200 - 600 pF Min 75 75 80 Max 300 300 125 Unit ns ns % 95 3355A-USB-5/03 Figure 20. Low-speed Downstream Port Load RS TxD+ CL 3.6V 1.5 K Ohm RS TxDCL CL = 200 pF to 600 pF Table 32. USB Source Timings, Full-speed Operation Symbol TDRATE TFRAME TRFI TRFIADJ TDJ1 TDJ2 TFDEOP TDEOP TJR1 TJR2 TFEOPT TFEOPR TFST Note: Parameter Full Speed Data Rate(1) Frame Interval (1) (1) Condition Average Bit Rate Min 11.97 0.9995 Max 12.03 1.0005 42 126 Unit Mb/s ms ns ns ns Consecutive Frame Interval Jitter No clock adjustment With clock adjustment -3.5 -4 -2 -2 -18.5 -9 160 82 Consecutive Frame Interval Jitter(1) Source Diff Driver Jitter To Next Transition For Paired Transitions Source Jitter for Differential Transition to SEO Transitions Differential to EOP Transition Skew Receiver Data Jitter Tolerance To Next Transition For Paired Transitions Source SEO interval of EOP Receiver SEO interval of EOP Width of SEO interval during differential transition 3.5 4 5 5 18.5 9 175 ns ns ns ns ns 14 ns 1. With 6.000 MHz, 100 ppm crystal. 96 AT43USB325 3355A-USB-5/03 AT43USB325 Figure 21. Differential Data Jitter TPERIOD Differential Data Lines Crossover Points Consecutive Transitions N*TPERIOD + TXJR1 Paired Transitions N*TPERIOD + TXJR2 Figure 22. Differential-to-EOP Transition Skew and EOP Width TPERIOD Crossover Point Extended Differential Data Lines Diff. Data-toSE0 Skew N*TPERIOD + TDEOP Source EOP Width: TFEOPT T LEOPT Receiver EOP Width: TFEOPR T LEOPR Figure 23. Receiver Jitter Tolerance TPERIOD Differential Data Lines TJR Consecutive Transitions N*TPERIOD + TJR1 Consecutive Transitions N*TPERIOD + TJR1 TJR1 TJR2 97 3355A-USB-5/03 Table 33. Hub Timings, Full-speed Operation Symbol THDD2 THDJ1 THDJ2 TFSOP TFEOPD TFHESK Parameter Hub Differential Data Delay without cable Hub Diff Driver Jitter to Next Transition for Paired Transitions Data Bit Width Distortion after SOP Hub EOP Delay Relative to THDD Hub EOP Output Width Skew -3 -1 -5 0 -15 Condition Min Max 44 3 1 5 15 15 Unit ns ns ns ns ns Table 34. Hub Timings, Low-speed Operation Symbol TLHDD TLHDJ1 TLHDJ2 TLUHJ1 TLUHJ2 TSOP TLEOPD TLHESK Parameter Hub Differential Data Delay Downstr Hub Diff Driver Jitter to Next Transition, downst for Paired Transitions, downst to Next Transition, upstr for Paired Transitions, upstr Data Bit Width Distortion after SOP Hub EOP Delay Relative to THDD Hub EOP Output Width Skew -45 -15 -45 -45 -60 0 -300 Condition Min Max 300 45 15 45 45 60 200 300 Unit ns ns ns ns ns 98 AT43USB325 3355A-USB-5/03 AT43USB325 Table 35. Hub Event Timings Symbol TDCNN Parameter Time to detect a downstream port connect event Time to detect a disconnect event on downstream port Awake Hub Suspended Hub Time from detecting downstream resume to rebroadcast Duration of driving reset to a downstream device Time to evaluate device speed after reset Time to detect a long K from upstream Time to detect a long SEO from upstream Duration of repeating SEO upstream Duration of sending SEO upstream after EOF1 Only for a SetPortFeature (PORT_RESET) request 10 2.5 2.5 2.5 Condition Min 2.5 Max 2000 Unit s TDDIS 2.5 2.5 2000 12000 s TURSM 100 s TDRST TDSPDEV TURLK TURLSEO TURPSEO TUDEOP 20 1000 5.5 5.5 23 2 s s s s FS bits FS bits 99 3355A-USB-5/03 Figure 24. Hub Differential Delay, Differential Jitter and SOP Distortion Upstream End of Cable VSS Differential Data Lines VSS A. Downstream Hub Delay With Cable Downstream Port VSS Crossover Point Upstream Port VSS Hub Delay Upstream THDD2 Crossover Point Crossover Point 50% Point of Initial Swing Hub Delay Downstream THDD1 B. Upstream Hub Delay Without Cable Downstream Port VSS Upstream Port or End of Cable VSS Crossover Point Hub Delay Upstream THDD1,THDD2 Crossover Point C. Upstream Hub Delay with or without Cable Figure 25. Hub EOP Delay and EOP Skew 50% Point of Initial Swing Upstream End of Cable VSS Downstream Port VSS A. Upstream EOP Delay with Cable TEOPTEOP+ Upstream Port VSS Downstream Port VSS B. Downstream EOP Delay without Cable TEOPTEOP+ Crossover Point Extended Crossover Point Extended Downstream Port VSS Upstream Port or End of Cable VSS TEOP Crossover Point Extended TEOP+ Crossover Point Extended C. Upstream EOP Delay with or without Cable 100 AT43USB325 3355A-USB-5/03 AT43USB325 Ordering Information Program Memory SRAM Mask ROM Ordering Code AT43USB325E-AC AT43USB325M-AC Package 64 LQFP 64 LQFP Operation Range Commercial (0C to 70C) Commercial (0C to 70C) 101 3355A-USB-5/03 Packaging Information 64AA - LQFP Dimensions in Millimeters and (Inches) Controlling Dimensions: Millimeters JEDEC STANDARD MS-026 ACB PIN 1 ID 12.25(0.492) SQ 11.75(0.463) PIN 1 0.50(0.020) BSC 0.27(0.011) 0.17(0.007) 10.10(0.397) SQ 9.90(0.389) 1.60(0.063) MAX 0.20(0.008) 0.09(0.003) 0~7 0.75(0.030) 0.45(0.018) 0.15(0.006) 0.05(0.002) REV. A 2325 Orchard Parkway San Jose, CA 95131 TITLE 64AA, 64-lead, Low-profile (1.4 mm) Plastic Quad Flat 1/15/2002 REV. A DRAWING NO. 64AA R Package (LQFP) 102 AT43USB325 3355A-USB-5/03 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 literature@atmel.com Web Site http://www.atmel.com Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. (c) Atmel Corporation 2003. All rights reserved. Atmel (R) and combinations thereof, and AVR (R) are the registered trademarks of Atmel Corporation or its subsidiaries. Kemet (R) is the registered trademark of Kemet Corporation. Panasonic (R) is the registered trademark of Matsushita Electric Industrial Co., Ltd. DigiKey (R) is the registered trademark of DigiKey Corporation. Jameco (R) Electronics is the registered trademark of James Electronics, LTD. Other terms and product names may be the trademarks of others. Printed on recycled paper. 3355A-USB-5/03 xM |
Price & Availability of AT43USB325
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |